Kengo Fukuda

发表

Verification of the accuracy of the estimated axle weights by a method for in-motion vehicles by using miniature experimental models

Tetsuya Kinugasa, Kyohei Imakura, Isamu Nomura, 2017 .

COST ANALYSIS ON REFINERY TREATMENT AND FINAL DISPASAL OF DRIFTING AND LANDING DEBRIS

Satoru Suzuki, Masayuki Saitou, Kengo Fukuda, 2008 .

806 Linear Response Model for an Axle Weighing System in Consideration of Moving Loads

Tetsuya Kinugasa, Toshiro Ono, Kengo Fukuda, 2007 .

The accuracy of an estimation method for the axle weights for in-motion vehicles by using a miniature model

Tetsuya Kinugasa, Ryota Hayashi, Kyohei Imakura, 2017 .

2A1-B04 A Control Strategy for Torque-unit Manipulators by Using Trajectory Planning and Parameter Identification(New Control Theory and Motion Control)

Koichi Osuka, Tetsuya Kinugasa, Kengo Fukuda, 2012 .

614 On an Instrumental Vehicle Model for Studies of Estimation Methods of Axle Weights for In-motion Vehicles

Tetsuya Kinugasa, Kengo Fukuda, Koji Yoshida, 2015 .

A NEW WEIGHING METHOD FOR CHECKWEIGHERS BY USING SIGNAL PROCESSING

Tetsuya Kinugasa, Toshiro Ono, Kengo Fukuda, 2009 .

A miniature axle weighing system for the examination of the accuracy of an estimation method of axle weight for in-motion vehicles: -A miniature model with two detecting parts-

Tetsuya Kinugasa, Kyohei Imakura, Kengo Fukuda, 2018 .

549 Evaluation of Estimates Obtained by Using Signal Processing Methods for Estimating Axle Weights of In-motion Vehicles

Tetsuya Kinugasa, Toshiro Ono, Kengo Fukuda, 2008 .

PLANNING OF MOTION TRAJECTORIES FOR THE CONTROL OF TORQUE-UNIT MANIPULATOR

Kengo Fukuda, Koji Yoshida, Yotaro Katayama, 2011 .

A Control Strategy for Torque-unit Manipulators

Koichi Osuka, Tetsuya Kinugasa, Kengo Fukuda, 2013 .

A New Method of Mass Measurement for Checkweighers

Tetsuya Kinugasa, Toshiro Ono, Kengo Fukuda, 2010 .

G101021 Development of miniature experimental models for improving estimation methods of axle weights of in-motion vehicle with using axle weighing system

Kengo Fukuda, Koji Yoshida, Tomoyuki Sato, 2013 .

G1000501 Development and Experiments of Miniature Models for Estimation Method of Axle Weights for In-Motion Vehicles

Kengo Fukuda, Koji Yoshida, Shinsaku Fujimoto, 2015 .

701 On the Accurate Estimation method of Axle weight for In-motion Vehicles Using Miniature Models

Tetsuya Kinugasa, Kengo Fukuda, Koji Yoshida, 2013 .

601 Development and experiments of miniature models for improvement of the estimation method of axle weights for in-motion vehicles

Tetsuya Kinugasa, Kengo Fukuda, Koji Yoshida, 2016 .

518 An Miniature Model for Improving Estimation Methods of Axle Weights of In-motion Vehicles

Tetsuya Kinugasa, Kengo Fukuda, Koji Yoshida, 2014 .

617 On a Model of Axle Weighting System for Studies of Estimation Methods of Axle Weights for In-motion Vehicles

Tetsuya Kinugasa, Kengo Fukuda, Koji Yoshida, 2015 .

Accuracy examination of an estimation method of axle weights for in-motion vehicles by using miniature experimental models

Ryota Hayashi, Kengo Fukuda, Koji Yoshida, 2018 .

517 An Miniature Weighbridge for Improving Estimation Methods of Axle Weights of In-motion Vehicles

Tetsuya Kinugasa, Hiroki Matsumoto, Kengo Fukuda, 2014 .

The weighing algorism using notch filters (On the improvement of the ability of weighing for checkweighers)

Tetsuya Kinugasa, Kengo Fukuda, Koji Yoshida, 2016 .

Axle Weighing of In-motion Vehicles

Toshiro Ono, Kengo Fukuda, Koichi Kameoka, 2002 .

TweezersDevice: A Device Facilitating Pick and Move Manipulation in Spatial Works

Fumihisa Shibata, Asako Kimura, Hideyuki Tamura, 2008 .

Effects of Aspect and Camber Ratios on Hydrodynamic Characteristics of Biplane-type Otter Board.

Kengo Fukuda, Fuxiang Hu, Tadashi Tokai, 1999 .

Experimental energy harvesting from fluid flow by using two vibrating masses

Kengo Fukuda, Yoshiki Nishi, Wataru Shinohara, 2017 .