Babur Ozcelik

发表

Warpage optimization of a bus ceiling lamp base using neural network model and genetic algorithm

Hasan Kurtaran, Babur Ozcelik, Tuncay Erzurumlu, 2005 .

The performance of different tool holders in dry milling

Babur Ozcelik, Bilgin Tolga Simsek, Emel Kuram, 2012 .

The effect of extreme pressure added vegetable based cutting fluids on cutting performance in milling

Babur Ozcelik, Bilgin Tolga Simsek, Emel Kuram, 2013 .

Comparison of the warpage optimization in the plastic injection molding using ANOVA, neural network model and genetic algorithm

Babur Ozcelik, Tuncay Erzurumlu, B. Ozcelik, 2006 .

Effects of different cooling conditions on twist drill temperature

Babur Ozcelik, Eyup Bagci, B. Ozcelik, 2007 .

Selection of optimal cutting conditions by using GONNS

Ibrahim N. Tansel, Babur Ozcelik, W. Y. Bao, 2006 .

Fuzzy logic and regression modelling of cutting parameters in drilling using vegetable based cutting fluids

Babur Ozcelik, Emel Kuram, E. Kuram, 2013 .

Transformations in machining. Part 2. Evaluation of machining quality and detection of chatter in turning by using s-transformation

Ibrahim N. Tansel, Babur Ozcelik, Xiaoyu Wang, 2006 .

The statistical modeling of surface roughness in high-speed flat end milling

Babur Ozcelik, Mahmut Bayramoglu, B. Ozcelik, 2006 .

Optimum surface roughness in end milling Inconel 718 by coupling neural network model and genetic algorithm

Hasan Kurtaran, Babur Ozcelik, Hasan Oktem, 2005 .

Detecting chatter and estimating wear from the torque of end milling signals by using Index Based Reasoner (IBR)

Ibrahim N. Tansel, Babur Ozcelik, Mustafa Demetgul, 2012 .

Analysis of temperature changes on the twist drill under different drilling conditions based on Taguchi method during dry drilling of Al 7075-T651

Babur Ozcelik, Eyup Bagci, B. Ozcelik, 2005 .

Influence of cutting parameters on drill bit temperature in dry drilling of AISI 1040 steel material using statistical analysis

Babur Ozcelik, Eyup Bagci, B. Ozcelik, 2007 .

Examination of the movement of a woven fabric in the horizontal direction using a non-contact end-effector

Babur Ozcelik, Fehmi Erzincanli, 2005 .

Optimization of surface roughness in drilling using vegetable‐based cutting oils developed from sunflower oil

Babur Ozcelik, Emel Kuram, E. Kuram, 2011 .

Optimization of injection parameters for mechanical properties of specimens with weld line of polypropylene using Taguchi method

Babur Ozcelik, B. Ozcelik, 2011 .

Effects of tool paths and machining parameters on the performance in micro-milling of Ti6Al4V titanium with high-speed spindle attachment

Babur Ozcelik, Emel Kuram, 2016 .

Analysis of temperature changes on the twist drill under different drilling conditions based on Taguchi method during dry drilling of Al 7075-T651

Babur Ozcelik, Eyup Bagci, 2005 .

Evaluation of vegetable based cutting fluids with extreme pressure and cutting parameters in turning of AISI 304L by Taguchi method

Babur Ozcelik, Emel Kuram, M. Huseyin Cetin, 2011 .

Minimization of warpage and sink index in injection-molded thermoplastic parts using Taguchi optimization method

Babur Ozcelik, Tuncay Erzurumlu, B. Ozcelik, 2006 .

Recyclability of Polyethylene/Polypropylene Binary Blends and Enhancement of Their Mechanical Properties by Reinforcement with Glass Fiber

Babur Ozcelik, Emel Kuram, Faruk Yilmaz, 2014 .

Environmentally Friendly Machining: Vegetable Based Cutting Fluids

Babur Ozcelik, Emel Kuram, E. Kuram, 2013 .

Investigating the effects of recycling number and injection parameters on the mechanical properties of glass-fibre reinforced nylon 6 using Taguchi method

Babur Ozcelik, Emel Kuram, Faruk Yilmaz, 2013 .

Experimental investigations of vegetable based cutting fluids with extreme pressure during turning of AISI 304L

Babur Ozcelik, Emel Kuram, M. Huseyin Cetin, 2011 .

Warpage and structural analysis of thin shell plastic in the plastic injection molding

Babur Ozcelik, B. Ozcelik, Ibrahim Sonat, 2009 .

Comparison of Dry and Wet End Milling of AISI 316 Stainless Steel

Babur Ozcelik, Bilgin Tolga Simsek, Emel Kuram, 2011 .

Influence of injection parameters and mold materials on mechanical properties of ABS in plastic injection molding

Babur Ozcelik, B. Ozcelik, E. Demirbas, 2010 .

Optimization of the Cutting Fluids and Parameters Using Taguchi and ANOVA in Milling

Babur Ozcelik, Bilgin Tolga Simsek, Emel Kuram, 2010 .

Optimization of machining parameters during micro-milling of Ti6Al4V titanium alloy and Inconel 718 materials using Taguchi method

Babur Ozcelik, Emel Kuram, E. Kuram, 2017 .

Effects of the Cutting Fluid Types and Cutting Parameters on Surface Roughness and Thrust Force

Babur Ozcelik, Emel Kuram, E. Kuram, 2010 .

Finite element and experimental investigation of temperature changes on a twist drill in sequential dry drilling

Babur Ozcelik, Eyup Bagci, B. Ozcelik, 2006 .