P. Nikolakopoulos

发表

Elastohydrodynamic analysis and Pareto optimization of intact, worn and misaligned journal bearings

P. Nikolakopoulos, C. Papadopoulos, L. Kaiktsis, 2011 .

Experimental and Analytical Investigations of Dynamic Characteristics of Magnetorheological and Nanomagnetorheological Fluid Film Journal Bearing

Dimitrios A. Bompos, P. Nikolakopoulos, 2016 .

Crack identification in frame structures

D. E. Katsareas, P. Nikolakopoulos, C. Papadopoulos, 1997 .

Journal Bearing Stiffness and Damping Coefficients Using Nanomagnetorheological Fluids and Stability Analysis

Dimitrios A. Bompos, P. Nikolakopoulos, 2014 .

Experimental and Analytical Investigations of Dynamic Characteristics of Magnetorheological and Nano Magnetorheological Fluid Film Journal Bearing

Dimitrios A. Bompos, P. Nikolakopoulos, 2014 .

Rotordynamic Analysis of a Shaft Using Magnetorheological and Nanomagnetorheological Fluid Journal Bearings

Dimitrios A. Bompos, P. Nikolakopoulos, 2016 .

Design of a PID Controller for a Linearized Magnetic Bearing

Epaminondas D. Mitronikas, Pantelis G. Nikolakopoulos, T. K. Psonis, 2015 .

A tribological study of piston rings lubricated by power law oils

P. Nikolakopoulos, A. Zavos, 2016 .

Measurement of friction and noise from piston assembly of a single-cylinder motorbike engine at realistic speeds

P. Nikolakopoulos, A. Zavos, 2018 .

Tribology of new thin compression ring of fired engine under controlled conditions-A combined experimental and numerical study

P. Nikolakopoulos, A. Zavos, 2018, Tribology International.

A control model of active magnetic bearings

Michael G. Farmakopoulos, P. Nikolakopoulos, A. Tzes, 2013 .

Comparison of Hertzian and JKR theories with a finite element model in boundary lubrication conditions between a compression ring and a cylinder

P. Nikolakopoulos, K. Grigoriadis, A. Zavos, 2018 .

Design, Modeling, and Evaluation of a Class-A Triaxial Force-Balance Accelerometer of Linear Based Geometry

P. Nikolakopoulos, E. Sokos, G. Dimitrakakis, 2022, Seismological Research Letters.

Prediction of crack depth and position in vibrating beams using artificial neural networks

P. Nikolakopoulos, A. Bouboulas, Nikolaos Anifantis, 2022, Diagnostyka.

A Tribological Simulation for a Typical Carbon Coated AFM Cantilever Interacting with a Monolayer Graphene Sheet

P. Nikolakopoulos, K. Grigoriadis, A. Zavos, 2018 .

Mechanical Behavior of B500c Steel with an Aluminum Layer Coating in a Marine Environment

P. Nikolakopoulos, C. Apostolopoulos, G. Diamantogiannis, 2015 .

Contact modeling with a finite element model in piston ring‒liner conjunction under dry conditions

P. Nikolakopoulos, K. Grigoriadis, A. Zavos, 2019, International Journal of Structural Integrity.

Experimental Measurements of Journal Bearing Friction Using Mineral, Synthetic, and Bio-Based Lubricants

Dimitrios A. Bompos, Pantelis G. Nikolakopoulos, P. Nikolakopoulos, 2015 .

Characterization of Stiffness and Damping in Textured Sector Pad Micro Thrust Bearings Using Computational Fluid Dynamics

Pantelis G. Nikolakopoulos, Lambros Kaiktsis, Christos I. Papadopoulos, 2012 .

Geometry Optimization of Textured Three-Dimensional Micro- Thrust Bearings

Pantelis G. Nikolakopoulos, Lambros Kaiktsis, Christos I. Papadopoulos, 2011 .

A dynamic and tribological simulation of a monolayer graphene sheet for a carbon atom‐graphene contact

P. Nikolakopoulos, K. Grigoriadis, A. Zavos, 2018, Lubrication Science.

CFD analysis of journal bearing hydrodynamic lubrication by Bingham lubricant

Pantelis G. Nikolakopoulos, C. A. Papadopoulos, K. P. Gertzos, 2008 .

Dynamic analysis of rotor–bearing systems lubricated with electrorheological fluids

P. Nikolakopoulos, C. Papadopoulos, Olga-Orsalia Christidi-Loumpasefski, 2017 .

Identification of wear and misalignment on journal bearings using artificial neural networks

C. A. Papadopoulos, A. J. Dentsoras, K. M. Saridakis, 2012 .

Aligned and Misaligned Wear Pattern in Fluid Film Bearings and Influence on the Rotor Response

Athanasios Chasalevris, C. A. Papadopoulos, Pantelis G. Nikolakopoulos, 2011 .

Fault Diagnosis of Journal Bearings Based on Artificial Neural Networks and Measurements of Bearing Performance Characteristics

C. A. Papadopoulos, A. J. Dentsoras, K. M. Saridakis, 2008 .

Non-linearities in misaligned journal bearings

Pantelis G. Nikolakopoulos, C. A. Papadopoulos, P. Nikolakopoulos, 1994 .

Wear identification in rotor-bearing systems by measurements of dynamic bearing characteristics

Athanasios Chasalevris, C. A. Papadopoulos, Pantelis G. Nikolakopoulos, 2011 .

Hysteretic Damping and Stress Evaluation of Rotor-Bearing Systems in the Resonance Zone

C. A. Papadopoulos, Pantelis G. Nikolakopoulos, G. D. Gounaris, 2014 .

Thermal–Hydrodynamic Behaviour of Coated Pivoted Pad Thrust Bearings: Comparison between Babbitt, PTFE and DLC

Stephanos Theodossiades, Konstantinos Katsaros, Dimitrios A. Bompos, 2018 .

Lubrication Performance of Engine Commercial Oils with Different Performance Levels: The Effect of Engine Synthetic Oil Aging on Piston Ring Tribology under Real Engine Conditions

Pantelis G. Nikolakopoulos, Anastasios Zavos, Stamatis Mavroudis, 2018, Lubricants.

CFD simulation of magnetorheological fluid journal bearings

Dimitrios A. Bompos, Pantelis G. Nikolakopoulos, P. Nikolakopoulos, 2011, Simul. Model. Pract. Theory.

Simulation of piston ring tribology with surface texturing for internal combustion engines

Pantelis G. Nikolakopoulos, Anastasios Zavos, P. Nikolakopoulos, 2015 .

Simulation of deposits effect on cylinder liner and influence on new and worn compression ring of a turbocharged DI engine

Pantelis G. Nikolakopoulos, P. Nikolakopoulos, 2021, Simul. Model. Pract. Theory.

Comparison of PID and Fuzzy PID Controller for a Linearised Magnetic Bearing

Pantelis G. Nikolakopoulos, Epaminondas D. Mitronikas, T. K. Psonis, 2017 .

On the tilting‐pad thrust bearings hydrodynamic lubrication under combined numerical and machine learning techniques

P. Nikolakopoulos, Konstantinos P. Katsaros, 2021, Lubrication Science.

Controllable high speed journal bearings, lubricated with electro-rheological fluids. An analytical and experimental approach

Pantelis G. Nikolakopoulos, C. A. Papadopoulos, P. Nikolakopoulos, 1998 .

A Review of Sensors Used on Fabric-Handling Robots

P. Nikolakopoulos, P. Koustoumpardis, Petros I. Kaltsas, 2022, Machines.

Axial Turbo-Expander Design for Organic Rankine Cycle Waste-Heat Recovery With Comparative Heavy-Duty Diesel Engine Drive-Cycle Performance Assessment

P. Nikolakopoulos, M. Deligant, C. Markides, 2021, Frontiers in Mechanical Engineering.

Investigation of the top compression ring power loss and energy consumption for different engine conditions

P. Nikolakopoulos, A. Zavos, 2021, Tribology - Materials, Surfaces & Interfaces.

Controllable Misaligned Journal Bearings, Lubricated with Smart Fluids

C. A. Papadopoulos, Pantelis G. Nikolakopoulos, P. Nikolakopoulos, 1997 .

Dynamic and tribological study of a planetary gearbox with local nonlinearities

Stephanos Theodossiades, Pantelis G. Nikolakopoulos, Konstantina Salagianni, 2017 .

Simulation and modeling of friction for honed and wave-cut cylinder bores of marine engines

Pantelis G. Nikolakopoulos, Anastasios Zavos, P. Nikolakopoulos, 2014, Simulation modelling practice and theory.

Cavitation effects on textured compression rings in mixed lubrication

Pantelis G. Nikolakopoulos, Anastasios Zavos, P. Nikolakopoulos, 2016 .

Effects of Surface Irregularities on Piston Ring- Cylinder Tribo Pair of a Two Stroke Motor Engine in Hydrodynamic Lubrication

P. Nikolakopoulos, A. Zavos, 2015 .

Tribological Characterization of Smooth and Artificially Textured Coated Surfaces Using Block-on-Ring Tests

P. Nikolakopoulos, A. Zavos, 2015 .

Synergistic Effect of Carbon Micro/Nano-Fillers and Surface Patterning on the Superlubric Performance of 3D-Printed Structures

P. Nikolakopoulos, K. Dassios, Katerina Gkougkousi, 2024, Materials.

Prediction of thrust bearing’s performance in Mixed Lubrication regime

P. Nikolakopoulos, Konstantinos P. Katsaros, 2024, Integrated Computer-Aided Engineering.