I. Korkut

发表

Application of regression and artificial neural network analysis in modelling of tool-chip interface temperature in machining

Ihsan Korkut, Adem Acir, Mehmet Boy, 2011, Expert Syst. Appl..

Determination of optimum cutting parameters during machining of AISI 304 austenitic stainless steel

I. Korkut, M. Kasap, I. Çiftçi, 2004 .

The influence of feed rate and cutting speed on the cutting forces, surface roughness and tool–chip contact length during face milling

I. Korkut, M. A. Donertas, 2007 .

Investigation of chip-back temperature during machining depending on cutting parameters

Ulvi Seker, Mehmet Boy, İhsan Korkut, 2007 .

High capacity three-component dynamometer design, construction and its calibration

I. Korkut, Y. Turgut, 2012 .

Experimental Examination of Main Cutting Force and Surface Roughness Depending on Cutting Parameters

I. Korkut, Mehmet Boy, 2008 .

End effector position calculation with the ANN for tapping machine

I. Korkut, M. Ozkan, Güllü Akkaş, 2021, Journal of Engineering Research.

The effect of cryogenic treatment on tapping

I. Korkut, G. Uzun, 2013 .

Thermo-mechanical stress analysis of rotating fiber reinforced variable thickness disk

I. Korkut, Ömer Can Farukoğlu, 2021, The Journal of Strain Analysis for Engineering Design.

Investigation of the effect of rake angle on main cutting force

Ulvi Seker, Mustafa Günay, Ersan Aslan, 2004 .

Irrigatıon in Agriculture and Automation Based Irrigation Systems (Mini-Review)

I. Korkut, Mustafa Arik, 2022, Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji.

The Influence of Cutting Parameters on Surface Roughness and Tool Wear In Milling of AISI D 2 Cold Work Tool Steels of Different Hardness

I. Korkut, Y. Turgut, 2012 .

A dynamometer design and its construction for milling operation

İhsan Korkut, I. Korkut, 2003 .

Elastic Stresses of Rotating Transversely Isotropic Fiber Reinforced Composite Cylinders

I. Korkut, Ömer Can Farukoğlu, 2020, International Journal of Engineering and Applied Sciences.

An Analytical Evaluation Method to Estimate Effects of Void Induced Errors on the Stresses of Pressurized Fiber Reinforced Composite Tube

I. Korkut, Ömer Can Farukoğlu, 2022, Materials Today Communications.

Analytical Solutions for Transversely Isotropic Fiber-Reinforced Composite Cylinders under Internal or External Pressure

I. Korkut, Ömer Can Farukoğlu, 2020, Journal of Polytechnic.

The Effects of Austempering Temperature and Time on the Machinability of Vermicular Graphite Iron

I. Korkut, A. Mavi, 2014 .

The effect of cryogenic treatment on tapping

I. Korkut, G. Uzun, 2012, The International Journal of Advanced Manufacturing Technology.

Using the Experimental Design Method to Optimize the Conicity and Circularity of Bored Holes

I. Korkut, Y. Kucuk, 2012, Arabian Journal for Science and Engineering.

Experimental Analysis of the Deviation from Circularity of Bored Hole Based on the Taguchi Method

İhsan Korkut, Yılmaz Küçük, I. Korkut, 2010 .

Optimization of Cutting Parameters in Face Milling with Neural Networks and Taguchi based on Cutting Force, Surface Roughness and Temperatures

Aslan Deniz Karaoglan, İhsan Korkut, Umit Yalcin, 2013 .

An experimental investigation into the machinability of GGG-70 grade spheroidal graphite cast iron

Kadir Yavuz, Yakup Turgut, İhsan Korkut, 2009 .

Developing Systematic Innovation in Moving Arm Design for Drone

I. Korkut, M. Günay, 2023, Journal of Polytechnic.

Experimental investigation of the effect of cutting tool rake angle on main cutting force

Ulvi Şeker, Ersan Aslan, İhsan Korkut, 2005 .

Using the Experimental Design Method to Optimize the Conicity and Circularity of Bored Holes

Ihsan Korkut, Yilmaz Kucuk, I. Korkut, 2012 .