S. Hardy

发表

Cyclic behaviour concerning the response of material subjected to tension levelling

J. W. Morris, A. Lees, S. Hardy, 2000 .

Static analysis of short beams

S. Hardy, M. Pipelzadeh, 1991 .

Low cycle fatigue life predictions for hollow tubes with axially loaded axisymmetric internal projections

S. Hardy, A. Gowhari-Anaraki, 1991 .

Determination of the constants of material models at high strain rates and elevated temperatures using shot impact test

S. Hardy, M. Pipelzadeh, G. Majzoobi, 2014 .

An assessment of simple material behaviour models for predicting the mechanical ratchetting of a stepped beam

S. Hardy, T. Hyde, J. Webster, 1985 .

Stress concentration factors due to axial loading of axisymmetric external projections on hollow tubes

Thomas H. Hyde, S J Hardy, R A Evans, 1987 .

Stress concentration factors and elastic-plastic stress and strain predictions for axisymmetric internal projections on hollow tubes subjected to axial loading

S. Hardy, A. Gowhari-Anaraki, 1989 .

Upper and Lower Bound Limit Loads for Thin-Walled Pressure Vessels Used for Aerosol Cans

S. Hardy, R. Abdusslam, 2009 .

Effects of tension levelling process parameters on cold rolled strip characteristics using a designed factorial analysis approach

S. Hardy, J. Thomas, J. Morris, 2005 .

A survey of post-peterson stress concentration factor data

S. J. Hardy, N. H. Malik, N. Malik, 1992 .

A new approach for the correction of stress–strain curves after necking in metals

S. Hardy, M. Pipelzadeh, G. Majzoobi, 2015 .

NUMERICAL MODELLING OF MECHANICAL RESPONSE OF A TWO-PHASE COMPOSITE

S. Hardy, T. Sadowski, E. Postek, 2006 .

A constitutive model for hardness considering the effects of strain, strain rate and temperature

S. Hardy, G. Majzoobi, S. Lahmi, 2015 .

A new model for the time-dependent behaviour of polycrystalline ceramic materials with metallic inter-granular layers under tension

S. Hardy, T. Sadowski, E. Postek, 2006 .

Prediction of the mechanical response of polycrystalline ceramics containing metallic intergranular layers under uniaxial tension

S. Hardy, T. Sadowski, E. Postek, 2005 .

Influence of runout table operation setup on hot strip quality, subject to initial strip condition: heat transfer issues

S. J. Hardy, S. D. Cox, D. J. Parker, 2001 .

The Effect of Stiffness on Stress Intensity Factor for a Crack in Annular Disc Under Constant Central Torque

S. Hardy, A. Sakhaee-Pour, A.R. Gowhari-Anaraki, 2010 .

Some fundamental considerations for the control of residual flatness in tension levelling

J. W. Morris, S. J. Hardy, J. T. Thomas, 2002 .

Experimental results and finite‐element predictions of the effect of nut geometry, washer and Teflon tape on the fatigue life of bolts

S J Hardy, M K Pipelzadeh, Gholam Hossein Farrahi, 2005 .

Influence of roll speed mismatch on strip curvature during the roughing stages of a hot rolling mill

A. W. Lees, S. J. Hardy, K. J. Brown, 2005 .

An assessment of the notch stress-strain conversion rules for short flat bars with projections subjected to axial and shear loading

S J Hardy, M K Pipelzadeh, S. Hardy, 1996 .

Experimental and analytical fatigue data for notched shafts in bending

A. R Gowhari-Anaraki, S J Hardy, M K Pipelzadeh, 2003 .

Mixed-mode fatigue crack propagation in thin T-sections under plane stress

S. Hardy, A. Gowhari-Anaraki, R. Adibi-Asl, 2003 .

Optimum Design of Composite-Reinforced Pressure Vessels

N. Malik, S. Hardy, 1990 .