S. Lu

发表

3D characterization of defects in deep-powder-bed manufactured Ti–6Al–4V and their influence on tensile properties

M. Brandt, M. Qian, J. Elambasseril, 2019, Materials Science and Engineering: A.

Microstructure and Mechanical Properties of Long Ti-6Al-4V Rods Additively Manufactured by Selective Electron Beam Melting Out of a Deep Powder Bed and the Effect of Subsequent Hot Isostatic Pressing

D. StJohn, M. Qian, S. Lu, 2015, Metallurgical and Materials Transactions A.

Additive manufacturing of a high niobium-containing titanium aluminide alloy by selective electron beam melting.

Ma Qian, M. Qian, S. Lu, 2015 .

High oxygen-content titanium and titanium alloys made from powder

M. Qian, S. Lu, S. Luo, 2020 .

Microstructure, tensile properties and deformation behaviour of a promising bio-applicable new Ti35Zr15Nb25Ta25 medium entropy alloy (MEA)

D. Fabijanic, S. Lu, B. Murdoch, 2021 .

Observation by an air-shower array in Tibet of the multi-TeV cosmic-ray anisotropy due to terrestrial orbital motion around the Sun.

Danzengluobu, Labaciren, Zhaxisangzhu, 2004, Physical review letters.

Formation of electric-field domains inGaAs∕AlxGa1−xAsquantum cascade laser structures

S. Lu, R. Hey, H. Grahn, 2006 .

Status report on the OPERA experiment

Yutaka S. Sato, S. Katsanevas, I. Budagov, 2001 .

The combined influence of elevated pre-sintering and subsequent bronze infiltration on the microstructures and mechanical properties of 420 stainless steel additively manufactured via binder jet printing

S. Lu, S. Nai, P. Wang, 2020 .

The changeable sheet detector in OPERA

S. Katsanevas, A. Ereditato, R. Klingenberg, 2002 .

MEASUREMENT OF SUB-PICOSECOND BUNCH LENGTH WITH THE INTERFEROMETRY FROM DOUBLE DIFFRACTION RADIATION TARGET*

S. Lu, A. Potylitsyn, G. Naumenko, 2012 .

Layer Additive Production or Manufacturing of Thick Sections of Ti-6Al-4V by Selective Electron Beam Melting (SEBM)

Y. Y. Sun, M. Qian, S. Lu, 2017 .

Intensified texture in selective electron beam melted Ti-6Al-4V thin plates by hot isostatic pressing and its fundamental influence on tensile fracture and properties

Y. Y. Sun, Pan Wang, M. Qian, 2019, Materials Characterization.

Characterization and decompositional crystallography of the massive phase grains in an additively-manufactured Ti-6Al-4V alloy

M. Qian, S. Lu, H. Tang, 2017 .

Massive transformation in Ti-6Al-4V additively manufactured by selective electron beam melting

Ma Qian, Ming Yan, David H. StJohn, 2016 .

Simulation-informed laser metal powder deposition of Ti-6Al-4V with ultrafine α-β lamellar structures for desired tensile properties

M. Brandt, M. Qian, S. Lu, 2021 .

Primary cosmic-ray composition in the energy range of 1014 eV to 1016 eV and high-energy atmospheric cosmic rays observed with emulsion chambers at Mt. Kanbala

M. Shibata, T. Shirai, S. Lu, 1987 .

Future plan for observation of cosmic gamma rays in the 100 TeV energy region with the Tibet air shower array : simulation and sensitivity

Danzengluobu, Labaciren, Zhaxisangzhu, 2007, 0710.2752.

Neutron diffraction structural analysis of Y/sub 2/Fe/sub 15/T/sub 2/C (T=Al,Ga,Si) alloys

S. Lu, W. Yelon, W. Chang, 1996 .

Fatigue Performance of Additively Manufactured Ti-6Al-4V: Surface Condition vs. Internal Defects

Y. Y. Sun, M. Leary, M. Qian, 2020, JOM.

Underground Prototype Water Cherenkov Muon Detector with the Tibet Air Shower Array

Danzengluobu, Labaciren, Zhaxisangzhu, 2009 .

A large underground water Cherenkov muon detector array with the Tibet air shower array for the gamma-ray astronomy in the 100-TeV region: Overview and physics goal

Danzengluobu, Labaciren, Zhaxisangzhu, 2008 .

Observation by an air-shower array in Tibet of the multi-TeV cosmic-ray anisotropy due to terrestrial orbital motion around the Sun.

Danzengluobu, Labaciren, Zhaxisangzhu, 2004, Physical review letters.

A large underground water Cherenkov muon detector array with the Tibet air shower array for Gamma-ray astronomy in the 100 TeV region: detector design and simulation

Danzengluobu, Labaciren, Zhaxisangzhu, 2008 .