A. Quattrocchi

发表

Self-heat generation of embedded piezoceramic patches used for fabrication of smart materials

Roberto Montanini, Fabrizio Freni, Antonino Quattrocchi, 2018, Sensors and Actuators A: Physical.

Air-coupled ultrasonic testing to estimate internal defects in composite panels used for boats and luxury yachts

R. Montanini, A. Quattrocchi, F. Freni, 2020, International Journal on Interactive Design and Manufacturing (IJIDeM).

Polyurethane Foams Loaded with Carbon Nanofibers for Oil Spill Recovery: Mechanical Properties under Fatigue Conditions and Selective Absorption in Oil/Water Mixtures

R. Montanini, A. Quattrocchi, A. Visco, 2021, Nanomaterials.

Experimental Investigation on the Bond Behavior of FRCM-Concrete Interface via Digital Image Correlation

R. Montanini, G. Ricciardi, A. Quattrocchi, 2021 .

Development and Experimental Validation of an Artificial Neural Network Model of a Microwave Microstrip Resonator for Humidity Sensing

Z. Marinković, A. Quattrocchi, G. Crupi, 2022, 2022 IEEE International Symposium on Medical Measurements and Applications (MeMeA).

A low-cost measurement system for microplastic detection in marine environment: A proof of concept

N. Donato, M. Latino, A. Quattrocchi, 2022, 2022 IEEE International Workshop on Metrology for the Sea; Learning to Measure Sea Health Parameters (MetroSea).

Measurement of the structural behaviour of a 3D airless wheel prototype by means of optical non-contact techniques

P. Chiariotti, M. Martarelli, P. Castellini, 2022, ACTA IMEKO.

Comparison between 3D-reconstruction optical methods applied to bulge-tests through a feed-forward neural network

R. Montanini, A. Quattrocchi, F. Lo Savio, 2021, ACTA IMEKO.

Static and dynamic characterization of biomedical polyethylene laser welding using biocompatible nano-particles

L. Torrisi, R. Montanini, A. Quattrocchi, 2018 .

Experimental Characterization of the FRCM-Concrete Interface Bond Behavior Assisted by Digital Image Correlation

Dario De Domenico, Roberto Montanini, Antonino Recupero, 2021, Sensors.

Mechanical Characterization of Nanocomposite Joints Based on Biomedical Grade Polyethylene under Cyclical Loads

R. Montanini, A. Quattrocchi, A. Visco, 2020, Polymers.

Response to fatigue stress of biomedical grade polyethylene joints welded by a diode laser.

Roberto Montanini, Annamaria Visco, Antonino Quattrocchi, 2018, Journal of the mechanical behavior of biomedical materials.

Experimental characterization of cantilever-type piezoelectric generator operating at resonance for vibration energy harvesting

Roberto Montanini, Antonino Quattrocchi, R. Montanini, 2016 .

Comparison between air-coupled ultrasonic testing and active thermography for defect identification in composite materials

R. Montanini, A. Quattrocchi, F. Freni, 2019 .

A New Approach for Impedance Tracking of Piezoelectric Vibration Energy Harvesters Based on a Zeta Converter

Antonio Testa, Roberto Montanini, Salvatore De Caro, 2020, Sensors.

R&D evaluation methodology based on group-AHP with uncertainty pdf

Gian Marco Revel, Marco Arnesano, Lorenzo Scalise, 2021, ArXiv.

Power Conversion Efficiency of Cantilever-Type Vibration Energy Harvesters Based on Piezoceramic Films

Roberto Montanini, Fabrizio Freni, Antonino Quattrocchi, 2021, IEEE Transactions on Instrumentation and Measurement.

Investigating Additive Manufactured Lattice Structures: A Multi-Instrument Approach

Enrico Primo Tomasini, Gianluca Rossi, Simone Pasinetti, 2020, IEEE Transactions on Instrumentation and Measurement.

PMMA-coated fiber Bragg grating sensor for measurement of Ethanol in liquid solution: manufacturing and metrological evaluation

R. Montanini, N. Donato, M. Latino, 2021 .

Development and verification of self-sensing structures printed in additive manufacturing: a preliminary study

R. Montanini, A. Quattrocchi, 2023, Acta IMEKO.

Structural Characterization of Complex Lattice Parts by Means of Optical Non-Contact Measurements

Gianluca Rossi, Roberto Marsili, Roberto Montanini, 2020, 2020 IEEE International Instrumentation and Measurement Technology Conference (I2MTC).

Qualification of additive manufactured trabecular structures using a multi-instrumental approach

Enrico Primo Tomasini, Gianluca Rossi, Paolo Castellini, 2019, 2019 IEEE International Instrumentation and Measurement Technology Conference (I2MTC).

A match coefficient approach for damage imaging in structural components by ultrasonic synthetic aperture focus

Annamaria Pau, Simone Sternini, F. Lanza di Scalea, 2017 .

Development and characterisation of a self-powered measurement buoy prototype by means of piezoelectric energy harvester for monitoring activities in a marine environment

R. Montanini, A. Quattrocchi, D. Alizzio, 2021, ACTA IMEKO.

Development of an Inkjet-Printed Interdigitated Device: CAD, Fabrication, and Testing

Z. Marinković, N. Donato, A. Quattrocchi, 2021, 2021 IEEE International Conference on Integrated Circuits, Technologies and Applications (ICTA).

Time stability of the dynamic behaviour of a 3D-printed airless wheel by stereolithography

P. Chiariotti, M. Martarelli, P. Castellini, 2023, Acta IMEKO.

Neural Modeling of the Surface Acoustic Wave Resonator Admittance Parameters

Z. Marinković, N. Donato, A. Quattrocchi, 2021, 2021 15th International Conference on Advanced Technologies, Systems and Services in Telecommunications (TELSIKS).