Yuan Ma

发表

Prediction of surface residual stress after end milling based on cutting force and temperature

Pingfa Feng, Dingwen Yu, Yuan Ma, 2016 .

Modeling of machining distortion for thin-walled components based on the internal stress field evolution

Jianfu Zhang, P. Feng, Dingwen Yu, 2019, The International Journal of Advanced Manufacturing Technology.

Initial residual stress measurement based on piecewise calculation methods for predicting machining deformation of aeronautical monolithic components

Liping Wang, P. Feng, Yuan Ma, 2020, The International Journal of Advanced Manufacturing Technology.

Energy criteria for machining-induced residual stresses in face milling and their relation with cutting power

Jianfu Zhang, Zhijun Wu, P. Feng, 2015 .

Frequency coupling design of ultrasonic horn with spiral slots and performance analysis of longitudinal-torsional machining characteristics

Jianfu Zhang, P. Feng, Yuan Ma, 2020 .

Study on the evolution of residual stress in successive machining process

Jianfu Zhang, P. Feng, Dingwen Yu, 2018 .

Prediction and control of surface roughness for the milling of Al/SiC metal matrix composites based on neural networks

Xiaohao Wang, P. Feng, Min Zhang, 2020, Advances in Manufacturing.

Research on Whole-Process Tensile Behavior of Headed Studs in Steel–Concrete Composite Structures

Yuan Ma, Hongbing Chen, R. Ding, 2021 .

Effectiveness of Oxygen during Sintering of Silver Thin Films Derived by Nanoparticle Ink

P. Feng, Yuan Ma, Xing Gao, 2022, Nanomaterials.

Research of Multi-Point Temperature Control Method in the Heating System of 3D Glass Hot Bending Machine

P. Feng, F. Feng, Yuan Ma, 2021, Journal of Physics: Conference Series.

Online chatter monitor system based on rapid detection method and wireless communication

P. Feng, Yuan Ma, Feng Feng, 2022, The International Journal of Advanced Manufacturing Technology.

Influence of tool inclination angle and cutting direction on long thin-walled part’s dimensional and geometric accuracy when high-speed ball end milling the heat-treated titanium alloy Ti–6Al–4 V

P. Feng, Yuan Ma, Sarwar Ali Abbasi, 2016 .

Utilization of heat quantity to model thermal errors of machine tool spindle

K. Zhou, P. Feng, Chao Xu, 2018 .

An improved material constitutive model for simulation of high-speed cutting of 6061-T6 aluminum alloy with high accuracy

P. Feng, Yuan Ma, Daochun Xu, 2015, The International Journal of Advanced Manufacturing Technology.

Frequency coupling design of ultrasonic horn with spiral slots and performance analysis of longitudinal-torsional machining characteristics

Jianfu Zhang, P. Feng, Yuan Ma, 2020, The International Journal of Advanced Manufacturing Technology.

Influence of microstructure and hardness on machinability of heat-treated titanium alloy Ti-6Al-4V in end milling with polycrystalline diamond tools

Jianfu Zhang, Zhijun Wu, P. Feng, 2016 .

Performance improvement of carbide cutting tool for Ti6Al4V alloys using electromagnetic treatment

P. Feng, F. Feng, Yuan Ma, 2021, The International Journal of Advanced Manufacturing Technology.

A novel approach for chatter online monitoring using coefficient of variation in machining process

Chao Xu, Pingfa Feng, Yuan Ma, 2018 .

Research on chip formation parameters of aluminum alloy 6061-T6 based on high-speed orthogonal cutting model

P. Feng, Wenbin Li, Yuan Ma, 2014 .

Kinematics and Simulation Analysis of Longitudinal-Torsional Ultrasonic Assisted Grinding of Zirconia Ceramics

P. Feng, F. Feng, Yuan Ma, 2022, Journal of Physics: Conference Series.

Initial guess by improved population-based intelligent algorithms for large inter-frame deformation measurement using digital image correlation

Jiaqing Zhao, Pan Zeng, Liping Lei, 2012 .

Cable Reinforced Small Scale Horizontal Axial Wind Turbine

Yuan Ma, Pan Zeng, Hong Ya Lu, 2013 .

A friction model having multiple factors for high-speed cutting of aluminum alloy 6061-T6

P. Feng, Wenbin Li, Chao Xu, 2016 .

Machining GLARE fibre metal laminates: a comparative study on drilling effect between conventional and ultrasonic-assisted drilling

J. Sinke, Yuan Ma, Ugur Koklu, 2022, The International Journal of Advanced Manufacturing Technology.

Wear Reduction by Toughness Enhancement of Disc Tool in Nomex Honeycomb Composites Machining

P. Feng, Yuan Ma, Jie Xu, 2023, Tribology International.

A novel approach for chatter online monitoring using coefficient of variation in machining process

P. Feng, Yuan Ma, Chao Xu, 2018, The International Journal of Advanced Manufacturing Technology.

An improved material constitutive model for simulation of high-speed cutting of 6061-T6 aluminum alloy with high accuracy

P. Feng, Wenbin Li, Yuan Ma, 2015 .

Research on chip formation parameters of aluminum alloy 6061-T6 based on high-speed orthogonal cutting model

P. Feng, Yuan Ma, Daochun Xu, 2014, The International Journal of Advanced Manufacturing Technology.

Energy criteria for machining-induced residual stresses in face milling and their relation with cutting power

Jianfu Zhang, P. Feng, Yuan Ma, 2015, The International Journal of Advanced Manufacturing Technology.

FEM Analysis of Residual Stress Distribution and Cutting Forces in Orthogonal Cutting with Different Initial Stresses

P. Feng, Yuan Ma, D. Yu, 2014 .

Tool Wear Characteristics and Strengthening Method of the Disc Cutter for Nomex Honeycomb Composites Machining with Ultrasonic Assistance

P. Feng, Yuan Ma, Jie Xu, 2022, Technologies.

Influence of microstructure and hardness on machinability of heat-treated titanium alloy Ti-6Al-4V in end milling with polycrystalline diamond tools

Jianfu Zhang, Zhijun Wu, P. Feng, 2016, The International Journal of Advanced Manufacturing Technology.

Utilization of heat quantity to model thermal errors of machine tool spindle

P. Feng, Yuan Ma, Chao Xu, 2018, The International Journal of Advanced Manufacturing Technology.