N. Fang

发表

A New Computational Intelligence Approach to Predicting the Machined Surface Roughness in Metal Machining

P. Pai, N. Fang, 2018 .

Slip-line modeling of machining with a rounded-edge tool—Part I: new model and theory

N. Fang, 2003 .

A comparative study of the cutting forces in high speed machining of Ti–6Al–4V and Inconel 718 with a round cutting edge tool

N. Fang, Q. Wu, N. Fang, 2009 .

A New Quantitative Sensitivity Analysis of the Flow Stress of 18 Engineering Materials in Machining

N. Fang, N. Fang, 2005 .

Wavelet-Based Denoising of Vibration Signals for Tool-Edge Wear Detection in High Speed Machining of Inconel 718

N. Fang, P. Srinivasa, N. Edwards, 2011 .

Numerical simulations and cutting experiments on single point diamond machining of semiconductors and ceramics

Eric R. Marsh, J. Patten, N. Fang, 2007 .

Interfacial debonding constitutive model and XFEM simulation for mesoscale concrete

Qing Zhang, X. Gu, N. Fang, 2021 .

A non-averaging method of determining the rheological properties of traction fluids

N. Fang, Liming Chang, M. Webster, 1999 .

Nonlinear Analysis of Interfacial Cracks

J. Bassani, N. Fang, 1997 .

The effect of built-up edge on the cutting vibrations in machining 2024-T351 aluminum alloy

P. Srinivasa Pai, Ning Fang, S. Mosquea, 2010 .

A comparative study of sharp and round-edge tools in machining with built-up edge formation: cutting forces, cutting vibrations, and neural network modeling

Ning Fang, P. Srinivasa Pai, S. Mosquea, 2011 .

On the Stress Concentration Factors of Rolling Element Bearing Cages

N. Fang, D. Pugh, R. Themudo, 2007 .

Cross-sectional nanoindentation: a new technique for thin film interfacial adhesion characterization

José M. Martínez-Esnaola, Antonio Martín-Meizoso, D. Pantuso, 1999 .

An experimental/theoretical approach to modelling the viscous behaviour of liquid lubricants in elastohydrodynamic lubrication contacts

N. Fang, Liming Chang, M. Webster, 2001 .

An experimental/theoretical approach to modeling the viscous behavior of liquid lubricants under EHL conditions

G. J. Johnston, N. Fang, Liming Chang, 2001 .

A damage evolution law enriched by microscopic mechanisms for structured sand in mechanical loading

M. Jiang, N. Fang, Zhifu Shen, 2019, Acta Geotechnica.

A general boundary approach to the construction of Michell truss structures

P. Dewhurst, P. Dewhurst, S. Srithongchai, 2009 .

Slip-line modeling of machining with a rounded-edge tool—Part II: analysis of the size effect and the shear strain-rate

N. Fang, N Fang, 2003 .

Prediction of built-up edge formation in machining with round edge and sharp tools using a neural network approach

P. Srinivasa Pai, N. Fang, N. Edwards, 2010, Int. J. Comput. Integr. Manuf..

Effect of tool edge wear on the cutting forces and vibrations in high-speed finish machining of Inconel 718: an experimental study and wavelet transform analysis

Ning Fang, P. Srinivasa Pai, S. Mosquea, 2011 .

Improvement of algorithm and prediction precision of an extended Oxley’s theoretical model

Bin Li, Jie Wang, Ning Fang, 2015 .

The effects of chamfered and honed tool edge geometry in machining of three aluminum alloys

N. Fang, Q. Wu, N. Fang, 2005 .

Sensitivity Analysis of the Material Flow Stress in Machining

N. Fang, 2003 .

Influence of the geometrical parameters of the chip groove on chip breaking performance using new-style chip formers

Ning Fang, N. Fang, 1998 .

Discussion

S. Bair, N. Fang, L. Chang, 2003 .

Surface roughness evaluation using cutting vibrations in high speed turning of Ti-6Al-4V - an experimental approach

P. Pai, G. D'Mello, N. Fang, 2016 .

A universal slip-line model with non-unique solutions for machining with curled chip formation and a restricted contact tool

P.L.B. Oxley, I. S. Jawahir, N. Fang, 2001 .

Slip-line modeling of built-up edge formation in machining

Peter Dewhurst, N. Fang, P. Dewhurst, 2005 .

Machining with tool–chip contact on the tool secondary rake face—Part I: a new slip-line model

N. Fang, N. Fang, 2002 .

An Analytical Predictive Model and Experimental Validation for Machining with Grooved Tools Incorporating the Effects of Strains, Strain-rates, and Temperatures

N. Fang, I. S. Jawahir, I. Jawahir, 2002 .

PREDICTIVE MODELING OF MACHINING PERFORMANCE IN TURNING OPERATIONS

I. S. Jawahir, M. Redetzky, O. W. Dillon, 1998 .

A comparative study of high-speed machining of Ti–6Al–4V and Inconel 718 - part I: effect of dynamic tool edge wear on cutting forces

P. Pai, N. Fang, N. Edwards, 2013 .

Tool-Edge Wear and Wavelet Packet Transform Analysis in High-Speed Machining of Inconel 718

P. Srinivasa Pai, N. Edwards, Ning Fang, 2012 .

Tool-chip friction in machining with a large negative rake angle tool

Ning Fang, N. Fang, 2005 .

Characteristic Variations of Chip Morphology and Cutting Forces in Face Milling with Flat-Faced and Grooved Tool Inserts

Ning Fang, N. Fang, 2003 .

An Improved Immune-Genetic Algorithm for the Traveling Salesman Problem

Jin-gui Lu, Ning Fang, Dinghong Shao, 2007, Third International Conference on Natural Computation (ICNC 2007).

Multidimensional signal processing and modeling with neural networks in metal machining: Cutting forces, vibrations, and surface roughness

P. Srinivasa Pai, N. Edwards, N. Fang, 2016, 2016 8th IEEE International Conference on Communication Software and Networks (ICCSN).

Neural Network Modeling and Prediction of Surface Roughness in Machining Aluminum Alloys

Ning Fang, P. Srinivasa Pai, N. Edwards, 2016 .

Characterization of the strain rate sensitivity of basal, prismatic and pyramidal slip in Zircaloy-4 using micropillar compression

Yang Liu, N. Fang, F. Giuliani, 2023, Materials Science and Engineering: A.