C. Eckelman

发表

Holding strength of screws in plywood and oriented strandboard

Y. Z. Erdil, Jilei Zhang, C. Eckelman, 2002 .

Customer satisfaction using QFD: an e‐banking case

G. Quesada, M. E. González, C. Eckelman, 2004 .

Bending Moment Capacity of L-Shaped Mitered Frame Joints Constructed of MDF and Particleboard

C. Eckelman, M. Derikvand, 2015 .

Inorganic-bonded composite wood panel systems for low-cost housing: a Central American perspective

Carl A. Eckelman, A. Ramirez-Coretti, R. W. Wolfe, 1998 .

Evaluation of the gluability of pressure steam-dried wood

H. N. Rosen, D. Cassens, C. Eckelman, 1986 .

Potential uses of laminated veneer lumber in furniture

Carl A. Eckelman, C. Eckelman, 1993 .

Staple holding strength of furniture frame joints constructed of plywood and oriented strandboard

Yusuf Ziya Erdil, Carl A. Eckelman, Jilei Zhang, 2003 .

Mechanical Properties of Knock-down Joints in Honeycomb Panels

Eva Haviarova, Carl A. Eckelman, Milan Šimek, 2013 .

The end distance effect of knock-down furniture fasteners on bending moment resistance of corner joints

Eva Haviarova, Carl A. Eckelman, Milan Šimek, 2008 .

Uses of the General Services Administration performance test method for upholstered furniture in the engineering of upholstered furniture frames

C. A. Eckelman, J. Zhang, C. Eckelman, 1995, Holz als Roh- und Werkstoff.

Uses of the General Services Administration performance test method for upholstered furniture in the engineering of upholstered furniture frames

C. Eckelman, J. Zhang, 1995 .

Bending moment capacity of rectangular mortise and tenon furniture joints

Y. Z. Erdil, C. Eckelman, Ali Kasal, 2005 .

Design and testing of bookcase frames constructed with round mortise and tenon joints

Ali Naci Tankut, Carl A. Eckelman, Nurgul Denizli-Tankut, 2003 .

Edge and face withdrawal strength of large screws in particleboard and medium density fiberboard

Carl A. Eckelman, C. Eckelman, Zaini Ithnin Bin Haji Abdul Rajak, 1993 .

Fatigue strength and allowable design stresses for some wood composites used in furniture

C. Eckelman, Z. Bao, H. Gibson, 1996, Holz als Roh- und Werkstoff.

A structural design model for sofa seat frames equipped with sinusoidal-type springs.

H. Gibson, Zhang Jilei, Lin FarChing, 2000 .

Material design factors for hardwood laminated-veneer-lumber

J. Youngquist, C. Eckelman, W. L. Hoover, 1987 .

Design and specification of hardwood laminated-veneer-lumber for furniture applications

Carl A. Eckelman, J. A. Youngquist, W. L. Hoover, 1988 .

Withdrawal and bending strength of dowel-nuts in plywood and oriented strandboard

Yusuf Ziya Erdil, Carl A. Eckelman, Jilei Zhang, 2003 .

The withdrawal strength of screws from a commercially available medium density fiberboard

C. A. Eckelman, C. Eckelman, 1988 .

Effect of cross holes on the strength of chair and table legs

Y. Z. Erdil, C. Eckelman, E. Haviarova, 2002 .

Performance testing of side chairs

C. A. Eckelman, C. Eckelman, 1999, Holz als Roh- und Werkstoff.

Bending Moment Capacities of L-Shaped Mortise and Tenon Joints under Compression and Tension Loadings

Ali Kasal, Eva Haviarova, Yusuf Ziya Erdil, 2015 .

Bending moment capacity of simple and haunched mortise and tenon furniture joints under tension and compression loads

Carl A. Eckelman, Mohammad Layeghi, Ghanbar Ebrahimi, 2014 .

EFFECT OF ADHESIVE TYPE AND TENON SIZE ON BENDING MOMENT CAPACITY AND RIGIDITY OF T-SHAPED FURNITURE JOINTS CONSTRUCTED OF TURKISH BEECH AND SCOTS PINE

Y. Z. Erdil, C. Eckelman, Ali Kasal, 2013 .

Effect of Tenon Geometry, Grain Orientation, and Shoulder on Bending Moment Capacity and Moment Rotation Characteristics of Mortise and Tenon Joints

Y. Z. Erdil, C. Eckelman, A. Ozcifci, 2012 .

Bending moment capacity of round mortise and tenon furniture joints

A. N. Tankut, Y. Z. Erdil, C. Eckelman, 2004 .

Technical Note: Static Versus Cyclic Load Capacity of Side Chairs Constructed with Mortise and Tenon Joints

Eva Haviarova, Yusuf Ziya Erdil, Carl A. Eckelman, 2013 .

Performance tests of school chairs constructed with round mortise and tenon joints

Eva Haviarova, Carl A. Eckelman, C. Eckelman, 2006 .

Design and testing of environmentally friendly wood school chairs for developing countries

Y. Z. Erdil, C. Eckelman, E. Haviarova, 2001 .

Theoretical analysis and design of joints in a representative sofa frame constructed of plywood and oriented strandboard

Ali Kasal, Yusuf Ziya Erdil, Carl A. Eckelman, 2008 .

PRODUCT ENGINEERING AND PERFORMANCE TESTING IN RELATION TO STRENGTH DESIGN OF FURNITURE

Eva Haviarova, Yusuf Ziya Erdil, Carl A. Eckelman, 2007 .

Bending strength of corner joints constructed with injection-molded splines

Carl A. Eckelman, F. Lin, C. Eckelman, 1997 .

WITHDRAWAL AND COMPRESSION FORCE CAPACITY OF PINNED END-TO-END ROUND MORTISE-AND-TENON WOODEN JOINTS

C. Eckelman, E. Haviarova, 2015 .

A comparison of the cyclic durability, ease of disassembly, repair, and reuse of parts of wooden chair frames

Eva Haviarova, Carl A. Eckelman, Mesut Uysal, 2015 .

Azeotropic Distillation Drying of Wood with Polar and Non-Polar Solvents

C. Eckelman, J. A. Galezewski, 2009 .

A technique for structural modeling of front rails for sofas

C. A. Eckelman, F.-C. Lin, J. Zhang, 2002, Holz als Roh- und Werkstoff.

Shear force and bending moment capacities of joints constructed with glued corner blocks

Y. Z. Erdil, C. Eckelman, Ali Kasal, 2006 .

Effect of number of fasteners on the strength of corner joints for cases

C. Eckelman, W. Q. Liu, 1998 .