R. Khettabi

发表

Effect of tool lead angle and chip formation mode on dust emission in dry cutting

J. Masounave, R. Khettabi, V. Songmene, 2007 .

18 Machining and Machinability of Aluminum Alloys

J. Kouam, R. Khettabi, V. Songmene, 2018 .

Fine and Ultrafine Particle Characterization and Modeling in High-Speed Milling of 6061-T6 Aluminum Alloy

R. Khettabi, V. Songmene, I. Zaghbani, 2009, Journal of Materials Engineering and Performance.

Modeling of Particle Emission During Dry Orthogonal Cutting

J. Masounave, R. Khettabi, V. Songmene, 2010 .

Influence of machining processes on particles emissions

J. Masounave, R. Khettabi, V. Songmene, 2010 .

ON CHIP FORMATION DURING DRILLING OF CAST ALUMINUM ALLOYS

J. Kouam, R. Khettabi, V. Songmene, 2013 .

Machining and Machinability of Aluminum Alloys

J. Kouam, R. Khettabi, V. Songmene, 2011 .

Prediction of machining performance using RSM and ANN models in hard turning of martensitic stainless steel AISI 420

Riad Khettabi, Mourad Nouioua, Mohamed Athmane Yallese, 2019, Proceedings of the Institution of Mechanical Engineers, Part C: Journal of Mechanical Engineering Science.

Cutting Conditions Modeling and Optimization in Hard Turning Using RSM, ANN and Desirability Function

Salim Belhadi, Riad Khettabi, Mohamed Athmane Yallese, 2018, Journal of Failure Analysis and Prevention.

Surface integrity of Al6061-T6 drilled in wet, semi-wet and dry conditions

Victor Songmene, Riad Khettabi, Jacques Masounave, 2013 .

Nanoparticle measurement, control and characterization

J. Kouam, M. Viens, J. Masounave, 2015 .

Optimization of Machining Process During Turning of X210Cr12 Steel Under MQL Cooling as a Key Factor in Clean Production

A. Chabbi, M. Yallese, Mourad Nouioua, 2017 .

Dust Generation Evaluation by a Predicting Model of Cutting Forces and Machining Temperature during Orthogonal Cutting of Aluminum Alloys

R. Khettabi, V. Songmene, A. Djebara, 2021 .

Experimental study of a turbo-alternator in industrial environment using cyclostationarity analysis

M. C. Djamaa, J. Antoni, A. Djebala, 2015, The International Journal of Advanced Manufacturing Technology.

Microstructure and crystallographic properties of Cu77Zn21 alloy under the effect of heat treatment

Y. El Mendili, R. Khettabi, K. Belmokre, 2018, Materials at High Temperatures.

Experimental study of a turbo-alternator in industrial environment using cyclostationarity analysis

Jérôme Antoni, Tarek Kebabsa, Nouredine Ouelaa, 2015 .

Comparative assessment of cooling conditions, including MQL technology on machining factors in an environmentally friendly approach

Tarek Mabrouki, Salim Belhadi, Riad Khettabi, 2017 .

Nanoparticle measurement, control and characterization: procedure applied to machining and mechanical friction

J. Kouam, M. Viens, J. Masounave, 2015 .

Investigation of the performance of the MQL, dry, and wet turning by response surface methodology (RSM) and artificial neural network (ANN)

Salim Belhadi, Riad Khettabi, Mourad Nouioua, 2017 .

Multi-response optimization using artificial neural network-based GWO algorithm for high machining performance with minimum quantity lubrication

Salim Belhadi, Riad Khettabi, Mourad Nouioua, 2021, The International Journal of Advanced Manufacturing Technology.

Multi-objective optimization of surface roughness, cutting forces, productivity and Power consumption when turning of Inconel 718

Salim Belhadi, Riad Khettabi, Mohamed Athmane Yallese, 2016 .

Design optimization for minimum technological parameters when dry turning of AISI D3 steel using Taguchi method

Tarek Mabrouki, Kamel Chaoui, Riad Khettabi, 2017 .

On the micro and nanoparticle emission during machining of titanium and aluminum alloys

J. Masounave, R. Khettabi, V. Songmene, 2013 .

Effect of Friction Testing of Metals on Particle Emission

J. Kouam, R. Khettabi, V. Songmene, 2012, Journal of Materials Engineering and Performance.

A new sustainability model for machining processes

Victor Songmene, Riad Khettabi, Imed Zaghbani, 2011 .

Effects of Speeds, Materials, and Tool Rake Angles on Metallic Particle Emission During Orthogonal Cutting

Victor Songmene, Riad Khettabi, Jacques Masounave, 2010 .

Investigation of the performance of the MQL, dry, and wet turning by response surface methodology (RSM) and artificial neural network (ANN)

Mohamed Lamine Bouhalais, M. Yallese, S. Belhadi, 2017, The International Journal of Advanced Manufacturing Technology.

Effect of MQL and dry processes on the particle emission and part quality during milling of aluminum alloys

Victor Songmene, Riad Khettabi, Mourad Nouioua, 2017 .

Effect of MQL and dry processes on the particle emission and part quality during milling of aluminum alloys

R. Khettabi, V. Songmene, A. Djebara, 2017, The International Journal of Advanced Manufacturing Technology.

Comparative assessment of cooling conditions, including MQL technology on machining factors in an environmentally friendly approach

M. Yallese, Tarek Mabrouki, S. Belhadi, 2017, The International Journal of Advanced Manufacturing Technology.