Z. Guo

发表

Characterisation of the 3-D dendrite morphology of magnesium alloys using synchrotron X-ray tomography and 3-D phase-field modelling

S. Xiong, Zhipeng Guo, Manhong Yang, 2015 .

Two- and three- dimensional studies of dendritic morphology in magnesium alloy by means of synchrotron X-ray microtomography and cellular automaton modelling

S. Xiong, Manhong Yang, Z. Guo, 2015 .

Correlation between Porosity and Fracture Mechanism in High Pressure Die Casting of AM60B Alloy

S. Xiong, Zhipeng Guo, Xiao-bo Li, 2016 .

Failure behavior of high pressure die casting AZ91D magnesium alloy

S. Xiong, Xiao-bo Li, Z. Guo, 2016 .

Quantitative phase-field lattice-Boltzmann study of lamellar eutectic growth under natural convection.

A. Zhang, Z. Guo, S. Xiong, 2018, Physical review. E.

Eutectic pattern transition under different temperature gradients: A phase field study coupled with the parallel adaptive-mesh-refinement algorithm

Shoumei Xiong, Aihua Zhang, S. Xiong, 2017 .

Effect of runner design on the externally solidified crystals in vacuum die-cast Mg-3.0Nd-0.3Zn-0.6Zr alloy

Z. Guo, Y. Zhou, S. Xiong, 2019, Journal of Materials Processing Technology.

On the growth mechanism of the primary silicon particle in a hypereutectic Al-20 wt%Si alloy using synchrotron X-ray tomography

S. Xiong, Z. Guo, J. Wang, 2018 .

Improved mechanical properties in vacuum-assist high-pressure die casting of AZ91D alloy

S. Xiong, Xiao-bo Li, Z. Guo, 2016 .

Determination of the interfacial heat transfer coefficient at the metal-sand mold interface in low pressure sand casting

S. Xiong, Z. Guo, A. Zhang, 2017 .

Study of dendritic growth and coarsening using a 3-D phase field model: Implementation of the Para-AMR algorithm

Z Guo, S M Xiong, Z. Guo, 2015 .

On the characterization of primary iron-rich phase in a high-pressure die-cast hypoeutectic Al-Si alloy

S. Xiong, S. Wiesner, Z. Guo, 2021 .

The characterization of Fe-rich phases in a high-pressure die cast hypoeutectic aluminum-silicon alloy

Z. Guo, S. Xiong, Chaofeng Liu, 2020 .

Characterization of high-pressure die-cast hypereutectic Al-Si alloys based on microstructural distribution and fracture morphology

Z. Guo, J. Wang, S. Xiong, 2019, Journal of Materials Science & Technology.

On the failure mechanism for high pressure die casting A390 hypereutectic alloy in low cycle and high cycle fatique

S. Xiong, L. Song, Z. Guo, 2018 .

Morphology transition of the primary silicon particles in a hypereutectic A390 alloy in high pressure die casting

Z. Guo, J. Wang, S. Xiong, 2017, Scientific Reports.

Modelling and simulation for die casting mould filling process using Cartesian cut cell approach

C. Bi, Z. Guo, S. Xiong, 2015 .

On the tensile failure induced by defect band in high pressure die casting of AM60B magnesium alloy

S. Xiong, Xia Li, Z. Guo, 2016 .

Morphology transition of the primary silicon particles in a hypereutectic A390 alloy in high pressure die casting

S. Xiong, Z. Guo, J. Wang, 2017, Scientific Reports.

Influence of slow-shot speed on PSPs and porosity of AlSi17Cu2.5 alloy during high pressure die casting

Junyou Wang, Z. Guo, J. Wang, 2019, Journal of Materials Processing Technology.

Ultrathin amorphous Ni–Ti film as diffusion barrier for Cu interconnection

M. Li, Liu Yang, Jingwei Chen, 2011 .