J. Gil-Sevillano

发表

Fragmentation of as-drawn pearlitic steel wires during torsion tests

I. Lefever, Etienne Aernoudt, E. Aernoudt, 1998 .

An analysis of the extrusion of bimetallic tubes by numerical simulation

J. Gil-Sevillano, J. Gil-Sevillano, J. L. Alcaraz, 1996 .

Adhesion studies in integrated circuit interconnect structures

J. Maiz, J. Molina-Aldareguia, I. Ocaña, 2007 .

Interface stability under biaxial loading of bilayered sheets between rigid surfaces—I. Bifurcation analysis

J. Martínez-Esnaola, J. Gil-Sevillano, J. L. Alcaraz, 1997 .

Interface stability under biaxial loading of bilayered sheets between rigid surfaces—II. Stability of perturbations

J. Martínez-Esnaola, J. Gil-Sevillano, J. L. Alcaraz, 1997 .

Cross-sectional nanoindentation: a new technique for thin film interfacial adhesion characterization

José M. Martínez-Esnaola, Antonio Martín-Meizoso, D. Pantuso, 1999 .

Simulation of Cross-Sectional Nanoindentation in Interconnect Structures with Cohesive Elements

J. Maiz, I. Ocaña, J. Martínez-Esnaola, 2006 .

Use of Nanoindentation to Characterise the Plasma Damage Region in Low-k Dielectric Films

F. Iacopi, M. V. Hove, Y. Travaly, 2006 .

Thermomechanical and microstructural properties of ZnCuTi under different deformation conditions.

J. Gil-Sevillano, T. Zühlke, 2015 .

Measurement and modelling of residual stresses in straightened commercial eutectoid steel rods

M. Elices, M. Daymond, R. Peng, 2005 .

An analytical approach to the stress field in the extrusion of bimetallic tubes

J. Martínez-Esnaola, J. Gil-Sevillano, J. L. Alcaraz, 1996 .

The influence of the primer layer on mechanical damage and loss of corrosion protection of deformed painted Zn-0.16% Al and Zn-5% Al galvanized sheet steel

J. Gil-Sevillano, D. Laverde, J. C. Zubillaga, 1995 .

Consolidation, microstructure and mechanical properties of newly developed TiB2-Based materials

F. Castro, J. Gil-Sevillano, José M. Sánchez, 1992 .

Residual stress profiling in the ferrite and cementite phases of cold-drawn steel rods by synchrotron X-ray and neutron diffraction

Manuel Elices, T. Buslaps, Ru Lin Peng, 2004 .

Modelling cleavage fracture of bainitic steels

Antonio Martín-Meizoso, A. Martín-Meizoso, I. Ocaña-Arizcorreta, 1994 .

Modelling the evolution of residual stresses during tensile testing of elastoplastic wires subjected to a previous bending operation

B. Goes, J. Gil-Sevillano, U. D'Haene, 1999 .

Safety maps in bimetallic extrusions

J. Gil-Sevillano, J. L. Alcaraz, 1996 .

On the influence of the mode of deformation on the hardening of iron at low temperature and large strains

E. Aernoudt, J. Gil-Sevillano, 1975 .

A fracture condition based on the upper bound method for the extrusion of bimetallic tubes

J. Martínez-Esnaola, J. Gil-Sevillano, J. L. Alcaraz, 1996 .

Assessment of the contribution of plastic strain gradient effects to the fatigue threshold of ductile materials

J. Martínez-Esnaola, J. Gil-Sevillano, I. Ocaña, 2013 .

A New Technique for the Characterization of the Adhesion in Integrated Circuit Interconnect Structures

J. Maiz, Jun He, J. Martínez-Esnaola, 2005 .

Calculation of shear textures with taylor-analysis

P. Houtte, E. Aernoudt, J. Gil-Sevillano, 1975 .

How a stable crack extension changes the Weibull modulus of cleavage fracture probability

A. Martín-Meizoso, J. Gil-Sevillano, M. Fuentes-Pérez, 1993 .

Controlled Crack Growth with a Dual-Tip Indenter

J. Martínez-Esnaola, A. Martín-Meizoso, J. Gil-Sevillano, 2013 .

Dual-Tip Elastic Indentation: A New Technique for Controlled Crack Growth and Brittle Fracture Toughness Determination

J. Martínez-Esnaola, A. Martín-Meizoso, J. Gil-Sevillano, 2001 .