Ship-Peng Lo

发表

The Application of an ANFIS and Grey System Method in Turning Tool-Failure Detection

Ship-Peng Lo, 2002 .

Effect of different tool flank wear lengths on the deformations of an elastic cutting tool and the machined workpiece

Zone-Ching Lin, Ship-Peng Lo, 2006, Int. J. Comput. Appl. Technol..

Quality prediction model of the sheet blanking process for thin phosphorous bronze

Yeou-Yih Lin, Ship-Peng Lo, Dar-Yuan Chang, 2007 .

Finite element modeling for chemical mechanical polishing process under different back pressures

Yeou-Yih Lin, Ship-Peng Lo, Ship-Peng Lo, 2003 .

An adaptive-network based fuzzy inference system for prediction of workpiece surface roughness in end milling

Ship-Peng Lo, Ship-Peng Lo, 2003 .

Strain and stress analysis of the oxide film surface in the chemical mechanical polishing process

Yeou-Yih Lin, Ship-Peng Lo, Cheng-Yung Chen, 2006, Int. J. Comput. Appl. Technol..

A hybrid model combining simulation and optimization in chemical mechanical polishing process

Yeou-Yih Lin, Ship-Peng Lo, Sheng-Li Lin, 2008 .

Modeling of chemical mechanical polishing process using FEM and abductive network

Yeou-Yih Lin, Ship-Peng Lo, Ship-Peng Lo, 2005, Eng. Appl. Artif. Intell..

A study of modularity operation of systems based on maintenance consideration

Yuo-Tern Tsai, K. S. Wang, Ship-Peng Lo, 2003 .

APPLICATION OF ABDUCTIVE POLYNOMIAL NETWORK AND GREY THEORY TO DRILL FLANK WEAR PREDICTION

Yeou-Yih Lin, Ship-Peng Lo, 2004, Appl. Artif. Intell..

Ultra-precision orthogonal cutting simulation for oxygen-free high-conductivity copper

Ship-Peng Lo, Zone-Chin Lin, 1997 .

Analysis of retaining ring using finite element simulation in chemical mechanical polishing process

Yeou-Yih Lin, Jen-Ching Huang, Ship-Peng Lo, 2007 .

Machining characteristics of Inconel 718 using ultrasonic and high temperature-aided cutting

Ship-Peng Lo, W. S. Lee, Ship-Peng Lo, 2008 .

An investigation of sticking behavior on the chip–tool interface using thermo-elastic–plastic finite element method

Yeou-Yih Lin, Ship-Peng Lo, Ship-Peng Lo, 2002 .

An analysis of cutting under different rake angles using the finite element method

Ship-Peng Lo, Ship-Peng Lo, 2000 .

A study of deformation of the machined workpiece and tool under different low cutting velocities with an elastic cutting tool

Zone-Ching Lin, Ship-Peng Lo, Ship-Peng Lo, 1998 .

Rapid measurement of surface roughness for face-milling aluminum using laser scattering and the Taguchi method

Ship-Peng Lo, Hsien-Yang Lin, Jinn-Tong Chiu, 2005 .

A study on the stress and nonuniformity of the wafer surface for the chemical-mechanical polishing process

Yeou-Yih Lin, Ship-Peng Lo, Ship-Peng Lo, 2003 .

A study of the tool-chip interface contact problem under low cutting velocity with an elastic cutting tool

Zone-Ching Lin, Ship-Peng Lo, Ship-Peng Lo, 1997 .

2-D discontinuous chip cutting model by using strain energy density theory and elastic-plastic finite element method

Zone-Ching Lin, Ship-Peng Lo, 2001 .

A study of a finite element model for the chemical mechanical polishing process

Ship-Peng Lo, Ship-Peng Lo, Y-Y Lin, 2004 .