Jun Luo

发表

Direct printing of surface-embedded stretchable graphene patterns with strong adhesion on viscous substrates

Hongcheng Lian, L. Qi, Ruirui Zhang, 2022, Journal of Industrial and Engineering Chemistry.

Fabricating patterned microstructures by embedded droplet printing on immiscible deformable surfaces

Hongcheng Lian, L. Qi, Ruirui Zhang, 2021, Journal of Industrial and Engineering Chemistry.

A ground-based work of droplet deposition manufacturing toward microgravity: Fine pileup of horizontally ejected metal droplets on vertical substrates

L. Qi, Jun Luo, Qi Lehua, 2021 .

Plasticity Improvement of CNTs/Mg Nanocomposite Materials Processed by Combining Friction Stir Processing and Ultrasonic-Assisted Extrusion

L. Qi, Jiming Zhou, Qian Zhang, 2021, Forming the Future.

Quantitatively characterizing the evolution of hole defects between overlapped aluminum droplets by a two-dimensional solidification model

Yibo Dou, Hongcheng Lian, L. Qi, 2022, Additive Manufacturing.

Design and printing of embedded conductive patterns in liquid crystal elastomer for programmable electrothermal actuation

Huayan Pu, Jiankang He, Jun Luo, 2022, Virtual and Physical Prototyping.

Evolution mechanism and elimination strategy for the directional effect in metal droplets horizontal deposition on vertical substrates

Hongcheng Lian, L. Qi, Jun Luo, 2023, International Journal of Heat and Mass Transfer.

Metal droplet printing of tube with high-quality inner surface via helical printing trajectory and soluble support

L. Qi, Huajun Cao, Jun Luo, 2022, Virtual and Physical Prototyping.

Three-dimensional numerical analysis and experimental confirmation for investigating the ground-based lateral droplet ejection toward microgravity simulation

L. Qi, X. Hou, Jun Luo, 2022, The Physics of Fluids.

Direct printing of graphene terahertz closed-ring resonator array from periodic single droplets via enhanced coffee-ring effect

Hongcheng Lian, Ruirui Zhang, Jun Luo, 2023, Carbon.

Evaluation of the segregation in printed mono-sized Al-In alloy droplets

Jun Luo, Lehua Qi, Yichen Wang, 2024, Journal of Materials Processing Technology.

Revisiting the inhomogeneity in drop-on-demand printing of graphene: An effective route for overcoming the coffee-ring effect

Hongcheng Lian, Ruirui Zhang, Jun Luo, 2024, Surfaces and Interfaces.

A Novel Stacked-graphene-line Printing Method Enabled by Droplet Ejection and Micro-pen Writing

Hongcheng Lian, Jun Luo, Xujiang Chao, 2023, 2023 IEEE International Conference on Manipulation, Manufacturing and Measurement on the Nanoscale (3M-NANO).

A highly stable and sensitive sensor with linear response enabled by embedded droplet printing and bio-inspired design

Hongcheng Lian, Ruirui Zhang, Jun Luo, 2024, Chemical Engineering Journal.

A new strategy for eliminating bottom hole defects during aluminum droplet printing within a broad temperature range

Yibo Dou, Hongcheng Lian, L. Qi, 2023, Journal of Materials Processing Technology.

Formation mechanism and elimination method of joint defects in lattice structures printed by metal droplet deposition manufacturing

Jun Luo, Lehua Qi, Lewen Yang, 2024, Journal of Manufacturing Processes.

Effect of Impinging Behavior between Annular Jet Shielding Gas and Printing Substrate on Metal Droplet Stable Ejection

Hongcheng Lian, Jun Luo, Lin Su, 2024, Additive Manufacturing.

Gas entrapment and pore formation in metal droplet-based 3D printing

Jun Luo, Lehua Qi, Hao Yi, 2023, International Journal of Mechanical Sciences.

A vertex-arc path planning method for metal droplet-based 3D printing of thin-walled parts with sharp corners

Yibo Dou, Hongcheng Lian, L. Qi, 2022, Journal of Materials Processing Technology.

A study on the solidification shapes of molten metal droplet impacting at low weber number

Jun Luo, Jieguang Huang, Lehua Qi, 2023, Physics of Fluids.