Sanjeev Kumar

发表

Investigation for obtaining the optimal solution for improving the performance of WEDM of super alloy Udimet-L605 using particle swarm optimization

Dixit Garg, Somvir Singh Nain, D. Garg, 2018 .

Improvement of Bearing Capacity of Shallow Foundation on Geogrid Reinforced Silty Clay and Sand

P. K. Kolay, Sanjeev Kumar, P. Kolay, 2013 .

Nonlinear Lateral Pile Deflection Prediction in Sands

Shamsher Prakash, Sanjeev Kumar, S. Prakash, 1996 .

ED Machining of Particulate Reinforced MMC’s

Sanjeev Kumar, Ajay Batish, Sarabjeet Singh Sidhu, 2014 .

Annual performance of an active solar distillation system

G. N. Tiwari, G. Tiwari, H. N. Singh, 2000 .

Effect of Multiwalled Carbon Nanotube in Cement Composite on Mechanical Strength and Freeze-Thaw Susceptibility

P. K. Kolay, Sunil Malla, Sanjeev Kumar, 2015 .

Analysis on the hazardous jarosite added concrete

Blessen Skariah Thomas, Priyansha Mehra, R. Gupta, 2018, Construction and Building Materials.

Performance Prediction of Eddy Current Flowmeter for Sodium

Geeta Vaidyanathan, Ravichandran Veerasamy, Prashant Sharma, 2009 .

Comparison of material transfer in electrical discharge machining of AISI H13 die steel

S. Kumar, B. Sethi, T. Singh, 2009 .

Study of heat and mass transfer from sugarcane juice for evaporation

G. N. Tiwari, Om Prakash, O. Prakash, 2003 .

Evaluation and Reduction of Liquefaction Potential at a Site in St. Louis, Missouri

Sanjeev Kumar, 2000 .

THE EFFECT OF DIFFERENT WIRE ELECTRODES ON THE MRR OF MS WORKPIECE USING WEDM PROCESS

Manpreet Singh, Sanjeev Kumar, Amandeep Singh Bansal, 2014 .

Surface modification of die steel materials by EDM method using tungsten powder-mixed dielectric

Uma Batra, Sanjeev Kumar, Sanjeev Kumar, 2012 .

Effect of Deep Cryogenic Treatment on the Surface Roughness of OHNS Die Steel after WEDM

Sanjeev Kumar, A. Thakur, Amoljit Singh Gill, 2012 .

Electric discharge machining of titanium and its alloys: a review

Ajay Batish, Rupinder Singh, Rupinder Singh, 2012 .

A mathematical model to predict material removal rate during electric discharge machining of cryogenically treated titanium alloys

Ajay Batish, Rupinder Singh, Rupinder Singh, 2015 .

Performance of high strength rubberized concrete in aggressive environment

Blessen Skariah Thomas, Priyansha Mehra, R. Gupta, 2015 .

Non-linear load-deflection prediction of single piles in sands, using subgrade reaction approach

Sanjeev Kumar, 1993 .

Properties of concrete containing polished granite waste as partial substitution of coarse aggregate

Praveen Kumar, Blessen Skariah Thomas, R. Gupta, 2017 .

Liquefaction of soils

Vijay K. Puri, Shamsher Prakash, Sanjeev Kumar, 1995 .

Prediction of wear and surface roughness in electro-discharge diamond grinding

Sounak Kumar Choudhury, S. K. Choudhury, Sanjeev Kumar, 2007 .

Effect of ballasting on performance characteristics of bias and radial ply tyres with zero sinkage

K. P. Pandey, Anil Kumar, Sanjeev Kumar, 2018, Measurement.

Evaluation of convective mass transfer coefficient during drying of jaggery

G. N. Tiwari, Om Prakash, O. Prakash, 2004 .

A hybrid Taguchi-artificial neural network approach to predict surface roughness during electric discharge machining of titanium alloys

Ajay Batish, Rupinder Singh, Rupinder Singh, 2014 .

Jarosite added concrete along with fly ash: Properties and characteristics in fresh state☆

Blessen Skariah Thomas, Priyansha Mehra, Ramesh Chandra Gupta, 2016 .