Sheng-Jye Hwang

发表

Adaptive process control of the changeover point for injection molding process

Yi-Sheng Chen, Kuo-Tsai Wu, Ming-Hong Tsai, 2019 .

Design with White Light-Emitting Diodes for an Automotive Low-Beam Projector Headlamp

Sheng-Jye Hwang, Huei-Huang Lee, Yueh Ying Chiang, 2016 .

Design and Development of Oral Appliance for Obstructive Sleep Apnea

Sheng-Jye Hwang, Huei-Huang Lee, Yu Bin Lai, 2013 .

Development of Barrel Heating via Induction in Injection Molding Machine

Sheng-Jye Hwang, Huy Tien Bui, 2015 .

Simulation and Design of Multiple-Station Rolling Forming for U-Section Steel Bar

Sheng-Jye Hwang, Huei-Huang Lee, Chin-Wei Lin, 2008 .

Study on Induction Heating Coil for Uniform Mold Cavity Surface Heating

Sheng-Jye Hwang, Huei-Huang Lee, Durn Yuan Huang, 2014 .

Design and simulation of electromagnetic linear actuators for jet dispensers

Sheng-Jye Hwang, Minh-Sang Tran, 2020 .

Pick-up Process Analysis of a Die Bonder

Yeong-Jyh Lin, Sheng-Jye Hwang, 2008 .

Development of a servo-hydraulic system with a self-tuning fuzzy PID controller to simulate injection molding process

Chien Jung Chen, Sheng-Jye Hwang, Kuo Tsai Wu, 2018, Microsystem Technologies.

Cutting force validation and volumetric errors compensation of thin workpieces with sensory tool holder

Sheng-Jye Hwang, Huei-Huang Lee, Yu-Wen Chen, 2020 .

Inversion for acoustic impedance of a wall by using artificial neural network

Gee-Pinn James Too, Sheng-Jye Hwang, S. R. Chen, 2007 .

Design and verification of a clamping system for micro-injection molding machine

Sheng-Jye Hwang, Huei-Huang Lee, Pei Chi Chang, 2006 .

Develop Potential Solution to the Engineering Conflicts of Additive Manufacturing by Using the Theory of Solution of Inventive Problems (TRIZ) - The Case of Material Jetting Process

Amy J. C. Trappey, Sheng-Jye Hwang, Yu Hui Wang, 2016 .

The 3D Printer Design and Model Formation by a Commercial Inkjet Printing Module

Wei-Hsiang Lai, Sheng-Jye Hwang, Sen-Yung Lee, 2008 .

Configuration synthesis of two-mode hybrid transmission systems with nine-link mechanisms

Sheng-Jye Hwang, Thanh-Tho Ho, 2019 .

Development of barrel heating system in injection molding machine via induction heating

Sheng-Jye Hwang, Huy Tien Bui, Sheng-Jye Hwang, 2015 .

Computer-Aided Design of a TSOP II LOC Package Using Taguchi’s Parameter Design Method to Optimize Mold-Flow Balance

Sheng-Jye Hwang, Francis Su, Hung Lung Lee, 2003 .

Design and Experiment of a Moving Magnet Actuator Based Jetting Dispenser

Sheng-Jye Hwang, Minh-Sang Tran, Sheng-Jye Hwang, 2019, Applied Sciences.

Prediction of paddle shift via 3-D TSOP modeling

Sheng-Jye Hwang, Huei-Huang Lee, Durn-Yuan Huang, 2000 .

An Efficient Solution for Wire Sweep Analysis in IC Packaging

Sheng-Jye Hwang, Francis Su, Jerry Su, 2003 .

Research of the behavior of solar module frame installed by solar clamping system by finite element method

Sheng-Jye Hwang, Li Chung Su, Chia Yu Chen, 2011 .

Configuration Synthesis of Novel Hybrid Transmission Systems Using a Combination of a Ravigneaux Gear Train and a Simple Planetary Gear Train

Sheng-Jye Hwang, Thanh-Tho Ho, Sheng-Jye Hwang, 2020, Energies.

Development of Liquid Spray Process in a Rapid Prototyping Machine

Sheng-Jye Hwang, Huei-Huang Lee, Durn Yuan Huang, 2012 .

Experimental investigation of infrared rapid surface heating for injection molding

Sheng-Jye Hwang, Sheng-Jye Hwang, P. Chang, 2006 .

P-V-T-C equation for epoxy molding compound

Sheng-Jye Hwang, Sheng-Jye Hwang, Yi-San Chang, 2006, IEEE Transactions on Components and Packaging Technologies.

Structure deformation of leadframe in plastic encapsulation

Sheng-Jye Hwang, Jian-Yu Chen, Y.J. Lee, 2007, 2007 International Microsystems, Packaging, Assembly and Circuits Technology.

Modeling a working coil coupled with magnetic flux concentrators for barrel induction heating in an injection molding machine

Sheng-Jye Hwang, Huy Tien Bui, Sheng-Jye Hwang, 2015 .

The influence of humidification and temperature differences between inlet gases on water transport through the membrane of a proton exchange membrane fuel cell

Wei-Hsiang Lai, Sheng-Jye Hwang, Sheng-Jye Hwang, 2015 .

Development of an external-type microinjection molding module for thermoplastic polymer

Sheng-Jye Hwang, Huei-Huang Lee, Pei Chi Chang, 2007 .

Warpage Prediction and Experiments of Fan-Out Waferlevel Package During Encapsulation Process

Sheng-Jye Hwang, Huei-Huang Lee, Shang-Shiuan Deng, 2013, IEEE Transactions on Components, Packaging and Manufacturing Technology.

Simulation of infrared rapid surface heating for injection molding

Sheng-Jye Hwang, Pei-Chi Chang, 2006 .

Prediction of Process Induced Warpage of Electronic Package by P-V-T-C Equation and Taguchi Method

Sheng-Jye Hwang, Huei-Huang Lee, Durn-Yuan Huang, 2006, 2006 International Conference on Electronic Materials and Packaging.

Three-Dimensional Paddle Shift Modeling for IC Packaging

Sheng-Jye Hwang, Sheng-Jye Hwang, Chien-Chang Pei, 2005 .

Wire density effect on wire sweep analysis for IC packaging

Sheng-Jye Hwang, Huei-Huang Lee, Durn-Yuan Huang, 2002, 2002 Proceedings. 8th International Advanced Packaging Materials Symposium (Cat. No.02TH8617).

Simulations and experiments of three-dimensional paddle shift for IC packaging

Sheng-Jye Hwang, Shiang-Yu Teng, Sheng-Jye Hwang, 2008 .

Study of warpage due to P-V-T-C relation of EMC in IC packaging

Sheng-Jye Hwang, Sheng-Jye Hwang, Li-Ching Hong, 2004 .