H. Kim

发表

Synthesis and Characterization of Si Oxide Coated Nano Ceria by Hydrolysis, and Hydrothermal Treatment at Low Temperature

M. Kong, H. Kim, 2017 .

Softening behavior of 8011 alloy produced by accumulative roll bonding process

Z. Xing, H. Kim, S. Kang, 2001 .

The complex microstructures in an as-cast Al–Mg–Si alloy

Yongwu Liu, H. Kim, S. Kang, 1999 .

Dissolution on the Surface of Bioceramics Prepared by Commercial Calcium Phosphate Powders

S. Seod, H. Kim, K. Leej, 2004 .

Corrosion Inhibiting Mechanism of Nitrite Ion on the Passivation of Carbon Steel and Ductile Cast Iron for Nuclear Power Plants

H. Y. Chang, K. T. Kim, Y. Kim, 2015 .

DENSIFICATION OF PRE-MIXED AND PREALLOYED Cu-12Sn BRONZE DURING MICROWAVE AND CONVENTIONAL SINTERING

R. Roy, A. Upadhyaya, H. Kim, 2002 .

The Effect of Ni Additions on the Microstructure and Castability of Low Si Added Al Casting Alloys

Y. Cho, J. Lee, H. Kim, 2015 .

Effect of natural aging and preaging on subsequent precipitation process of an AI-Mg-Si alloy with high excess silicon

L. Zhen, H. Kim, S. Kang, 1997 .

Effect of rolling speed on microstructure and age-hardening behaviour of Al–Mg–Si alloy produced by twin roll casting process

Chan‐Gyung Park, N. Lim, H. Kim, 2011 .

Effects of heat treatment on microstructure and mechanical properties of twin roll casted Al–5.5Mg–0.02Ti alloy

C. Park, N. Lim, H. Kim, 2010 .

Effect of the rolling speed on microstructural and mechanical properties of aluminum―magnesium alloys prepared by twin roll casting

J. Seol, C. Park, N. Lim, 2010 .

Microstructure and mechanical properties of Al–Mg alloy sheets for autobody application

H. Kim, S. Kang, D. Jiang, 1999 .

Precipitation behaviour of Al-Mg-Si alloys with high silicon content

W. Fei, L. Zhen, H. Kim, 1997 .

Microstructure and Mechanical Properties of Non‐Heat Treatable Aluminum Alloys Produced by Accumulative Roll Bonding Process

C. Lim, Z. Xing, H. Kim, 2013 .

A new approach to the design of a low Si-added Al–Si casting alloy for optimising thermal conductivity and fluidity

Y. Cho, M. S. Kim, J. M. Lee, 2015, Journal of Materials Science.

Effect of Secondary Carbide Addition on Properties of Ti(C0.7N0.3)-Ni Cermets

Shinhoo Kang, Sun-Yong Ahn, H. Kim, 2007 .

Influence of Filler Surface Treatments on Processability and Properties of Polymer-bonded Nd–Fe–B Magnets

J. Xiao, J. Otaigbe, S. Constantinides, 1999 .

Tensile and fatigue fracture behaviour of a spot welded Al-Mg alloy

H. Kim, D. Jiang, S. Kang, 1997 .

Microstructure and mechanical properties of spot welded Al–5·5Mg–0·3Cu alloy

H. Kim, D. Jiang, S. Kang, 1997 .

Structure and properties of AA3003 alloy produced by accumulative roll bonding process

Z. Xing, H. Kim, S. Kang, 2002 .

Structure stability of AA3003 alloy with ultra-fine grain size

Z. Xing, H. Kim, S. Kang, 2004 .

Properties of Aluminum Clad Sheets for Condenser Fins Fabricated with Transition Elements(Cu, Cr) added to Al-1.4Mn-1.0Zn Base Alloys

Y. Lee, K. Euh, H. Kim, 2014 .

Effect of Microstructure Control on the Tensile and Erosion Properties of 3527/4343 Aluminum Clad

K. Euh, H. Kim, Y. Oh, 2013 .