Frédéric Valiorgue

发表

Optimization of a drilling sequence under MQL to minimize the thermal distortion of a complex aluminum part

Pierre Faverjon, Joël Rech, Frédéric Valiorgue, 2015, Prod. Eng..

Modelling of Residual Stresses Induced by Turning of 316L

Hédi Hamdi, Jean-Michel Bergheau, Joël Rech, 2009 .

Local Global Method for the Prediction of Surface Residual Stresses in 3D Turning

Philippe Gilles, Eric Feulvarch, Joël Rech, 2014 .

Calibration of the insert/tool holder thermal contact resistance in stationary 3D turning

Michel Coret, Eric Feulvarch, Joël Rech, 2013 .

3D Numerical Prediction of Residual Stresses in Turning of 15-5PH

Eric Feulvarch, Joël Rech, Frédéric Valiorgue, 2011 .

Une nouvelle approche des conséquences thermomécaniques induites par les procédés d'usinage : application à la rectification et au to urnage.

Hédi Hamdi, Jean-Michel Bergheau, Frédéric Valiorgue, 2007 .

Chained Welding and Finish Turning Simulations of Austenitic Stainless Steel Components

Vincent Robin, Jean-Michel Bergheau, Joël Rech, 2013 .

CHARACTERIZATION OF FRICTION COEFFICIENT AND HEAT PARTITION COEFFICIENT BETWEEN AN AUSTENITIC STEEL AISI304L AND A TiN-COATED CARBIDE CUTTING TOOL

Pedro J. Arrazola, Joël Rech, Frédéric Valiorgue, 2012 .

Influence of ball burnishing on residual stress profile of a 15-5PH stainless steel

Joël Rech, Frédéric Valiorgue, Catherine Verdu, 2016 .

3D modeling of residual stresses induced in finish turning of an AISI304L stainless steel

Philippe Gilles, Hédi Hamdi, Jean-Michel Bergheau, 2012 .

Fatigue of Aluminum/Glass Fiber Reinforced Polymer Composite Assembly Joined by Self-piercing Riveting

Frédéric Valiorgue, Fabien Lefebvre, Philippe Michel, 2015 .

Improvement of the numerical modeling in orthogonal dry cutting of an AISI 316L stainless steel by the introduction of a new friction model

Hédi Hamdi, Joël Rech, Frédéric Valiorgue, 2008 .

Modeling of Surface Dynamic Recrystallisation During the Finish Turning of the 15-5PH Steel

Eric Feulvarch, Joël Rech, Frédéric Valiorgue, 2013 .

Identification of a friction model—Application to the context of dry cutting of an AISI 316L austenitic stainless steel with a TiN coated carbide tool

Hédi Hamdi, Jean-Michel Bergheau, Joël Rech, 2008 .

Emissivity calibration for temperatures measurement using thermography in the context of machining

Hédi Hamdi, Jean-Michel Bergheau, Joël Rech, 2013 .

Hybrid model for the prediction of residual stresses induced by 15-5PH steel turning

Eric Feulvarch, Joël Rech, Frédéric Valiorgue, 2012 .

A new approach for the modelling of residual stresses induced by turning of 316L austenitic stainless steel

Philippe Gilles, Hédi Hamdi, Jean-Michel Bergheau, 2008 .

Heat Flux Density Distribution Differences in Four Machining Processes of AlSi7 Block: MQL Drilling, Tapping, Reaming and Dry Milling☆

Sangil Han, Pierre Faverjon, Frédéric Valiorgue, 2017 .

A new approach for the modelling of residual stresses induced by turning of 316L

Hédi Hamdi, Jean-Michel Bergheau, Joël Rech, 2007 .

Emissivity calibration for temperature measurement using infrared thermography in orthogonal cutting of 316L and 100Cr6 grinding

Hédi Hamdi, Jean-Michel Bergheau, Joël Rech, 2011 .

Fatigue performance of a self-piercing rivet joint between aluminum and glass fiber reinforced thermoplastic composite

Frédéric Valiorgue, Fabien Lefebvre, Philippe Michel, 2016 .

Non-destructive inspection of initial defects of PA6.6-GF50/aluminum self-piercing riveted joints and damage monitoring under mechanical static loading

Frédéric Valiorgue, Patrick Lapeyronnie, Jean-Michel Roche, 2017 .