K. Doosthoseini

发表

Investigation on bonding quality of beech wood (Fagus orientalis L.) veneer during high temperature drying and aging

S. Mirshokraie, G. Koch, J. Welling, 2012, European Journal of Wood and Wood Products.

Manufacturing of bacterial nano-cellulose reinforced fiber−cement composites

E. Ganjian, M. Azin, F. Mohammadkazemi, 2015 .

EFFECT OF MAT MOISTURE CONTENT AND CU NANOPARTICLES ON HEAT TRANSFER AND PHYSICAL AND MECHANICAL PROPERTIES OF POPLAR PARTICLEBOARD

K. Doosthoseini, M. Farajallahpour, 2012 .

Evaluation of old corrugated container and wood fiber application on surface roughness of three-layer particleboard

H. Abdolzadeh, K. Doosthoseini, 2009, BioResources.

The influence of silane coupling agent and poplar particles on the wettability, surface roughness, and hardness of UF-bonded wheat straw (Triticum aestivum L.)/poplar wood particleboard

Seyedeh Masoumeh Hafezi, K. Doosthoseini, 2014, Journal of Forestry Research.

The effect of acetylated particle distribution and type of resin on physical and mechanical properties of poplar particleboard

A. Karimi, A. Enayati, H. Abdolzadeh, 2011, European Journal of Wood and Wood Products.

Particleboard manufacturing: an innovative way to recycle paper sludge.

A. Taramian, K. Doost-hoseini, Sayyed Ahmad Mirshokraii, 2007, Waste management.

Chemical changes of wood fibers after hydrothermal recycling of MDF wastes

B. Moezzipour, M. Ahmadi, A. Abdolkhani, 2017, Journal of the Indian Academy of Wood Science.

Using Na+MMT nanoclay as a secondary filler in plywood manufacturing

Hamid Zarea-Hosseinabadi, K. Doosthoseini, 2010, Journal of the Indian Academy of Wood Science.

THE EFFECT OF PARAFFIN ADDITION AND PRESSING CONDITIONS ON SOME PROPERTIES OF MEDIUM DENSITY FIBERBOARD (MDF) WITH EMPHASIS ON SURFACE ROUGHNESS

A. J. Latibari, M. Faezipour, A. Akrami, 2011 .

Optimization of Press time and Properties of Laminated Veneer Lumber Panels by Means of a Punching Technique

K. Doosthoseini, H. Pangh, 2017 .

Investigation on bonding quality of beech wood (Fagus orientalis L.) veneer during high temperature drying and aging

S. Mirshokraie, G. Koch, J. Welling, 2011, European Journal of Wood and Wood Products.

Low resin medium density fiberboard made from chemical activated hardwoods fibers

Payam Moradpour, Kazem Doosthoseini, Hamid Zarea-Hosseinabadi, 2010, Journal of the Indian Academy of Wood Science.

Correlation between gas and liquid permeability with noise reduction coefficient in insulation boards made from sugar cane bagasse

Reza Hosseinpourpia, H. R. Taghiyari, A. Elyasi, 2017 .

Correlation between sound absorption coefficients with physical and mechanical properties of insulation boards made from sugar cane bagasse

H. R. Taghiyari, K. Doost-hoseini, A. Elyasi, 2014 .

Measurement of Wood Cutting Forces during Bandsawing Using Piezoelectric Dynamometer

Asghar Tarmian, Frieder Scholz, Payam Moradpour, 2016 .

Cutting forces in bandsaw processing of oak and beech wood as affected by wood moisture content and cutting directions

F. Scholz, P. Moradpour, A. Tarmian, 2013, European Journal of Wood and Wood Products.

Wear resistance and friction coefficient of nano-SiO2 and ash-filled HDPE/lignocellulosic fiber composites

A. Abdulkhani, M. J. Sheykh, A. Tarmian, 2017, Polymer Bulletin.

Physical and mechanical properties of plywood manufactured from treated red-heart beech (Fagus orientalis L.) wood veneers

Gerald Koch, Kazem Doosthoseini, S. Mirshokraie, 2011, BioResources.

Drying Kinetics of Poplar (Populus Deltoides) Wood Particles by a Convective Thin Layer Dryer

Mohammad Layeghi, Kazem Doosthoseini, M. Layeghi, 2012 .

The effect of different kinds of nanosilica on practical properties of plywood

M. Faezipour, A. Tarmian, B. Moezzipour, 2013, Journal of the Indian Academy of Wood Science.

MALDI-TOF, 13C NMR and FT-MIR analysis and strength characterization of glycidyl ether tannin epoxy resins

A. Pizzi, L. Delmotte, A. Abdulkhani, 2016 .