Volker Gümmer

发表

Probabilistic CFD Simulation of a High-Pressure Compressor Stage Taking Manufacturing Variability Into Account

Alexander Lange, Matthias Voigt, Konrad Vogeler, 2010 .

Design Parameter Identification of the Air Supply for a Turboshaft Engine Quick-Start System

Volker Gümmer, M. Kerler, C. Schäffer, 2016 .

Numerical Investigation of End Wall Boundary Layer Removal on Highly Loaded Axial Compressor Blade Rows

Marius Swoboda, Volker Gümmer, M. Goller, 2008 .

Design of an Airworthy Turboshaft Engine Quick-Start System with Compact Pressurized Air Supply for Rotorcraft Application

Volker Gümmer, M. Kerler, C. Schäffer, 2016 .

Tip Gap Variation on a Transonic Rotor in the Presence of Tip Blowing

Volker Gümmer, Hans-Peter Kau, Cyril Guinet, 2014 .

Operational Aspects of an Engine Quick-Start System with Compact Air Supply for Rotorcraft Application

Volker Gümmer, M. Kerler, C. Schäffer, 2017 .

A method for tapping of bleed air and the aircraft engine with at least one device for withdrawal of bleed air

Volker Gümmer, Sascha Burghardt, 2014 .

Numerical and Experimental Investigations of a Compressor Cascade Flow With Secondary Air Removal

Bernd Becker, Volker Gümmer, Dragan Kožulović, 2013 .

Parametric Study of the Bleed Position in a Tip Blowing Casing Treatment

Volker Gümmer, Cyril Guinet, Valentin Bettrich, 2014 .

Design of a Highly-Loaded Four-Stage Low-Speed Research Compressor

Carsten Clemen, Konrad Vogeler, Henner Schrapp, 2008 .

Impact of Manufacturing Variability and Nonaxisymmetry on High-Pressure Compressor Stage Performance

Matthias Voigt, Alexander Lange, Matthias Voigt, 2012 .

Impact of Manufacturing Variability on Multistage High-Pressure Compressor Performance

Alexander Lange, Matthias Voigt, Konrad Vogeler, 2012 .

The potential of helicopter turboshaft engines incorporating highly effective recuperators under various flight conditions

Volker Gümmer, Chengyu Zhang, 2019 .

Using Sweep and Dihedral to Control Three-Dimensional Flow in Transonic Stators of Axial Compressors

Volker Gümmer, H.-P. Kau, U. Wenger, 2000 .

An Experimental Investigation of a Tandem Stator Flow Characteristic in a Low Speed Axial Research Compressor

Konrad Vogeler, Volker Gümmer, Jens Ortmanns, 2014 .

The Potential of Rotor and Stator Clocking in a 2.5-Stage Low-Speed Axial Compressor

Volker Gümmer, B. Becker, J. Städing, 2012 .

An Experimental Investigation of Stator Clocking Effects in a Two-Stage Low-Speed Axial Compressor

Volker Gümmer, G. Kosyna, B. Becker, 2011 .

Active Flow Control in a Single-Stage Axial Compressor Using Tip Injection and Endwall Boundary Layer Removal

Carsten Clemen, Volker Gümmer, B. Dobrzynski, 2008 .

Introduction of a Parameter Based Compressor Blade Model for Considering Measured Geometry Uncertainties in Numerical Simulation

Carsten Clemen, Alexander Lange, Konrad Vogeler, 2009 .

Impact of Manufacturing Variability and Non-Axisymmetry on High-Pressure Compressor Stage Performance

Matthias Voigt, Konrad Vogeler, Henner Schrapp, 2011 .

Experimental Investigation of Endwall and Suction Side Blowing in a Highly Loaded Compressor Stator Cascade

Carsten Clemen, Volker Gümmer, Rolf Radespiel, 2012 .

Impact of Manufacturing Variability on Multi–Stage High–Pressure Compressor Performance

Matthias Voigt, Konrad Vogeler, Henner Schrapp, 2012 .