Yifu Shen

发表

Code-switching and Translation: Taking Literary Text as an Example

Yifu Shen, 2019 .

MICROSTRUCTURE DEVELOPING MECHANISM IN SELECTIVE LASER SINTERING OF MULTI-COMPONENT Cu-BASED ALLOY POWDER

Yifu Shen, 2006 .

Effects of processing parameters on direct laser sintering of multicomponent Cu based metal powder

Yifu Shen, Yifu Shen, D. Gu, 2006 .

Investigation on dissimilar underwater friction stir lap welding of 6061-T6 aluminum alloy to pure copper

Xin Yao, Yifu Shen, Xin Yao, 2014 .

Influence of reinforcement weight fraction on microstructure and properties of submicron WC–Cop/Cu bulk MMCs prepared by direct laser sintering

Yifu Shen, Yifu Shen, D. Gu, 2007 .

Balling phenomena during direct laser sintering of multi-component Cu-based metal powder

Yifu Shen, Yifu Shen, D. Gu, 2007 .

In-situ TiC particle reinforced Ti-Al matrix composites: Powder preparation by mechanical alloying and Selective Laser Melting behavior

Yifu Shen, Zhiyang Wang, Yifu Shen, 2009 .

Balling phenomena in direct laser sintering of stainless steel powder: Metallurgical mechanisms and control methods

Yifu Shen, Yifu Shen, D. Gu, 2009 .

Preparation of TiN-Ti5Si3 in-situ composites by Selective Laser Melting

Zhijian G. Lu, Yifu Shen, Zhijian Lu, 2009 .

Improvements of mechanical properties in dissimilar joints of HDPE and ABS via carbon nanotubes during friction stir welding process

Jicheng Gao, Yifu Shen, Yifu Shen, 2015 .

Effect of rare earth oxide addition on microstructures of ultra-fine WC-Co particulate reinforced Cu matrix composites prepared by direct laser sintering

Yifu Shen, Yifu Shen, D. Gu, 2007 .

The dissimilar friction stir lap welding of 1A99 Al to pure Cu using Zn as filler metal with “pinless” tool configuration

Wenhua Chen, Xin Yao, Jicheng Gao, 2015 .

Dissimilar friction stir welding of Ti–6Al–4V alloy and aluminum alloy employing a modified butt joint configuration: Influences of process variables on the weld interfaces and tensile properties

Yifu Shen, Yifu Shen, Weiye Hu, 2014 .

Preparation of TiN – Ti 5 Si 3 in-situ composites by Selective Laser Melting

Yifu Shen, Zhijian Lu, Dongdong Gu, 2009 .

Microstructure and tensile properties of dissimilar submerged friction stir welds between HDPE and ABS sheets

Chao Li, Jicheng Gao, Yifu Shen, 2016, The International Journal of Advanced Manufacturing Technology.

A feasibility research on friction stir welding of a new-typed lap–butt joint of dissimilar Al alloys

Yifu Shen, Bo Li, Yifu Shen, 2012 .

Microstructural characteristics and formation mechanism of direct laser-sintered Cu-based alloys reinforced with Ni particles

Zhijian G. Lu, Yifu Shen, Zhijian Lu, 2009 .

Casting defects induced fatigue damage in aircraft frames of ZL205A aluminum alloy – A failure analysis

Bo Li, Yifu Shen, Yifu Shen, 2011 .

WC–Co particulate reinforcing Cu matrix composites produced by direct laser sintering

Yifu Shen, Yifu Shen, D. Gu, 2006 .

Growth morphologies and mechanisms of TiC grains during Selective Laser Melting of Ti–Al–C composite powder

Yifu Shen, Yifu Shen, D. Gu, 2009 .

Development of highly porous titanium scaffolds by selective laser melting

Ning Liu, Yan Wang, Yifu Shen, 2010 .