Jamil A. Khan

发表

Modeling and Simulation of Gas Turbine System on a Virtual Test Bed (VTB)

Roger A. Dougal, Eshwarprasad Thirunavukarasu, Ruixian Fang, 2012 .

Peak Demand Reduction with Dual-Source Heat Pumps Using Municipal Water

J. H. Morehouse, Jamil A. Khan, L. N. Connor, 1992 .

Thermal load deviation model for superheater and reheater of a utility boiler

Lijun Xu, Jamil A. Khan, Zhi-Hang Chen, 2000 .

Separation of copper from plastic waste material by air classification and water flotation

Jamil A. Khan, S. F. Lee, E. Maskalenko, 1996 .

Towards Ultra-compact High Heat Flux Microchannel Heat Sink

Ruixian Fang, Jamil A. Khan, A.K.M.M. Monjur Morshed, 2014 .

High Speed Turbo-Generator: Test Stand Simulator Including Turbine Engine Emulator

Richard Smart, Roger A. Dougal, Wei Jiang, 2010 .

Dynamic centrifugal compressor model for system simulation

Wei Jiang, Roger A. Dougal, Jamil A. Khan, 2006 .

Modeling of the Effect of Parallel Rib-Type Roughness on Local, Single-Phase Heat Transfer in Rod Bundles by CFD: Part 1—Flow Resistance

Jamil A. Khan, Leo A. Carrilho, 2010 .

ESRDC - Designing and Powering the Future Fleet

Roger A. Dougal, Chen Li, Enrico Santi, 2018 .

System Configuration and Performance Studies of Solid Oxide Fuel Cell -Gas Turbine Hybrid Cycle

Wei Jiang, Roger A. Dougal, Jamil A. Khan, 2007 .

A Piezoelectric Micropumping Device

Jamil A. Khan, Cuifang Kuang, M. Yakut Ali, 2009 .

Control Strategies for Start-Up and Part-Load Operation of Solid Oxide Fuel Cell/Gas Turbine Hybrid System

Wei Jiang, Roger A. Dougal, Ruixian Fang, 2010 .

Thermoelectric Model of a Tubular SOFC for Dynamic Simulation

Wei Jiang, Roger A. Dougal, Ruixian Fang, 2008 .

150. Estimating Emission Factors in a Capacitor Factory Using a Modified Two-Zone Model

Jamil A. Khan, Charles E. Feigley, M. Venkatraman, 2006 .

39. A User-Friendly Software for Indoor Air Exposure Assessment

Jamil A. Khan, Charles E. Feigley, S. Tamanna, 2003 .

Two and Three-Dimensional Simulations of Enhanced Heat Transfer in Nuclear Fuel Rod Bundles

Jamil A. Khan, Michael E. Conner, Milorad B. Dzodzo, 2009 .

185. Short-Term Sampling Time Requirements in Rooms

Jamil A. Khan, Charles E. Feigley, James R. Hussey, 2003 .

Nanoparticle Enhanced Ionic Liquids (NEILS) as Working Fluid for the Next Generation Solar Collector

Jamil A. Khan, J. Khan, Titan C. Paul, 2013 .

Prediction of nugget development during resistance spot welding using coupled thermal–electrical–mechanical model

Jamil A. Khan, Yuh J. Chao, Y. Chao, 1999 .

Thermal Modeling of Overlap Friction Stir Welding for Al-Alloys

Jamil A. Khan, J. Khan, Mir Zahedul H. Khandkar, 2001 .

Experimental investigation of the impact of geometrical surface modification on spray cooling heat transfer performance in the non-boiling regime

Jamil A. Khan, Nabeel M. Abdulrazzaq, Saad K. Oudah, 2019, International Journal of Heat and Mass Transfer.

Thermal analysis of flip-chip packaged 280 nm nitride-based deep ultraviolet light-emitting diodes

Jamil A. Khan, M. Asif Khan, Max Shatalov, 2005 .

ENHANCEMENT OF HEAT TRANSFER BY INSERTING A METAL MATRIX INTO A PHASE CHANGE MATERIAL

Jamil A. Khan, J. Khan, X. Tong, 1996 .

Enhancement of Heat Transfer with Inclined Baffles and Ribs Combined

Jamil A. Khan, Sarah C. Baxter, S. Baxter, 2002 .

The thermal modeling of a matrix heat exchanger using a porous medium and the thermal non-equilibrium model

Aly H. Shaaban, Jamil A. Khan, J. Khan, 2008 .

Predicting residual thermal stresses in friction stir welded metals

Michael A. Sutton, Jamil A. Khan, Anthony P. Reynolds, 2006 .

Evaluating the Thermal Characteristics of Copper-II and Zinc-Oxide Nanofluids Flowing Over a Heated Flat Plate

Aly H. Shaaban, Jamil A. Khan, Andrew M. Hayes, 2008 .

Numerical modeling of a rotary kiln incinerator

Jamil A. Khan, John S. Morse, D. Pal, 1993 .

Enhanced flow boiling in microchannels by self-sustained high frequency two-phase oscillations

Jamil A. Khan, Yoav Peles, Fanghao Yang, 2013 .

Numerical Thermal Model of Resistance Spot Welding in Aluminum

Jamil A. Khan, J. Khan, K. Broach, 2000 .

Thermal performance of ionic liquids for solar thermal applications

Jamil A. Khan, Ann E. Visser, J. Khan, 2014 .

Effects of inlet and exhaust locations and emitted gas density on indoor air contaminant concentrations

Jamil A. Khan, Charles E. Feigley, Mallik Ahmed, 2006 .

Prediction of temperature distribution and thermal history during friction stir welding: input torque based model

Jamil A. Khan, Anthony P. Reynolds, A. Reynolds, 2003 .

Evaluation of the radiative properties of a dispersed particulate medium for construction material applications

Jamil A. Khan, J. Khan, Bonnie K. Wiseman, 2003 .

Effective heat transfer in a metal-hydride-based hydrogen separation process

Jamil A. Khan, William H Fleming, Curtis A. Rhodes, 2001 .

An investigation of air inlet types in mixing ventilation

Jamil A. Khan, Charles E. Feigley, James R. Hussey, 2007 .

Two-Dimensional Effects on the Response of Packed Bed Regenerators

Jamil A. Khan, Donald E. Beasley, 1989 .

Numerical Simulation of Resistance Spot Welding Process

Jamil A. Khan, Y. Chao, J. Khan, 2000 .