Mohammed Nouari

Mohammed Nouari, Dominique Knittel, Mohamed Jaafar, 2018, 2018 IEEE 23rd International Conference on Emerging Technologies and Factory Automation (ETFA).

Characterization of the cutting forces generated during the gear hobbing process: Spur gear

A. Moufki, Naoual Sabkhi, Mohammed Nouari, 2015 .

A new friction law for sticking and sliding contacts in machining

A. Moufki, Mohammed Nouari, Alain Molinari, 2011 .

A Study of the BTA Deep Drilling Process through a Quantitative and Qualitative Analysis of the Chip Formation Process

Mohammed Nouari, Badis Haddag, Claude Barlier, 2013 .

Modeling of velocity-dependent chip flow angle and experimental analysis when machining 304L austenitic stainless steel with groove coated-carbide tools

Mohammed Nouari, Badis Haddag, Christophe Czarnota, 2013 .

Structural Modeling and Active Vibration Control of Smart FGM Plate through ANSYS

Mohammed Nouari, Kouider Bendine, Zouaoui Satla, 2017 .

Some cases of machining large-scale parts: Characterization and modelling of heavy turning, deep drilling and broaching

A. Moufki, Mohammed Nouari, Badis Haddag, 2016 .

Numerical Simulation of Incremental Sheet Forming by Simplified Approach

Mohammed Nouari, Jean-Louis Batoz, A. Delamézière, 2011 .

Toward a better understanding of tool wear effect through a comparison between experiments and SPH numerical modelling of machining hard materials

Mohammed Nouari, Michel Salaün, Christine Espinosa, 2009 .

Analysis of the heat transfer at the tool–workpiece interface in machining: determination of heat generation and heat transfer coefficients

Mohammed Nouari, Samir Atlati, Badis Haddag, 2015 .

Optimal cutting conditions when dry end milling the aeroengine material Ti–6242S

Mohammed Nouari, M. Nouari, A. Ginting, 2007 .

Influence of thermal conductivity on wear when machining titanium alloys

Mohammed Nouari, M. El Mansori, Hisham A. Abdel-Aal, 2009 .

The influence of solid lubricant for improving tribological properties in turning process

Mohammed Nouari, N. Suresh Kumar Reddy, M. Nouari, 2011 .

Effect of the third-body particles on the tool–chip contact and tool-wear behaviour during dry cutting of aeronautical titanium alloys

Mohammed Nouari, Ivan Iordanoff, I. Iordanoff, 2007 .

Analytical stochastic modeling and experimental investigation on abrasive wear when turning difficult to cut materials

Faycel Halila, Mohammed Nouari, Christophe Czarnota, 2013 .

Experimental and numerical analyses of the tool wear in rough turning of large dimensions components of nuclear power plants

Mohammed Nouari, Badis Haddag, Claude Barlier, 2014 .

Numerical prediction of the chip formation process and induced damage during the machining of carbon/epoxy composites

Mohammed Nouari, A. Delamézière, L. Ben Ayed, 2015 .

Hybrid modelling of sliding–sticking zones at the tool–chip interface under dry machining and tool wear analysis

A. Moufki, Mohammed Nouari, Alain Molinari, 2012 .

An elastoplastic constitutive damage model to simulate the chip formation process and workpiece subsurface defects when machining CFRP composites

Mohammed Nouari, Arnaud Delamézière, L. Ben Ayed, 2015 .

Finite element modelling of the thermo-mechanical behavior of coatings under extreme contact loading in dry machining

Mohammed Nouari, Badis Haddag, M. Nouari, 2011 .

Modelling of chip separation in machining unidirectional FRP composites by stiffness degradation concept

Mohammed Nouari, M. El Mansori, M. Mansori, 2009 .

Wear mechanisms in dry machining of aluminum alloys

Mohammed Nouari, F. Girot, G. List, 2003 .

Tool wear and heat transfer analyses in dry machining based on multi-steps numerical modelling and experimental validation

Mohammed Nouari, Badis Haddag, M. Nouari, 2013 .

Tribological behaviour and tool wear analyses in rough turning of large-scale parts of nuclear power plants using grooved coated insert

Mohammed Nouari, Badis Haddag, Hamid Makich, 2014 .

Effect of machining parameters and coating on wear mechanisms in dry drilling of aluminium alloys

Mohammed Nouari, Franck Girot, Daniel Gehin, 2005 .

Dry machinability of nickel-based weld-hardfacing layers for hot tooling

Mohammed Nouari, M. El Mansori, M. Mansori, 2007 .

Experimental verification of a diffusion tool wear model using a 42CrMo4 steel with an uncoated cemented tungsten carbide at various cutting speeds

Mohammed Nouari, Alain Molinari, A. Molinari, 2005 .

Tribo-energetic correlation of tool thermal properties to wear of WC-Co inserts in high speed dry machining of aeronautical grade titanium alloys

Mohammed Nouari, M. El Mansori, Hisham A. Abdel-Aal, 2009 .

Wear behaviour of cemented carbide tools in dry machining of aluminium alloy

Mohammed Nouari, Franck Girot, S. Gomez, 2005 .

The effect of thermal property degradation on wear of WC-CO inserts in dry cutting

Mohammed Nouari, M. El Mansori, Hisham A. Abdel-Aal, 2008 .

Impact of a diamond coating on tool wear behaviour during dry machining of a multidirectional composite materials

Mohammed Nouari, Franck Girot, D. Iliescu, 2006 .

Thermomechanical modelling of the tool–workmaterial interface in machining and its implementation using the \ABAQUS\ \VUINTER\ subroutine

Mohammed Nouari, Samir Atlati, Badis Haddag, 2014 .

Experimental and numerical studies on the performance of alloyed carbide tool in dry milling of aerospace material

Mohammed Nouari, M. Nouari, A. Ginting, 2006 .