A Vibration-Based PMN-PT Energy Harvester

We report design, modeling, analysis, and experimental study of a vibration-based piezoelectric energy harvester. The energy harvester is made of a composite cantilever of a single crystal relaxor ferroelectric material, (1- x)Pb(Mg1/3Nb2/3)O3-xPbTiO3 (PMN-PT), and a polydimethylsiloxane (PDMS) base layer. A PDMS proof mass is constructed at the tip of the composite cantilever beam and is used as a means to tune the system natural frequency. The use of the PMN-PT piezoelectric material and an interdigited electrodes (IDEs) design improves the energy conversion efficiency. A dynamic systems modeling approach is employed to analyze the responses and the performance of the harvester design. We have demonstrated that a prototype of the harvester with a size of 7.4 mm times 2 mm times 110 mum outputs a voltage of 10 V (0.3 mW power) under a vibration excitation with a peak-to-peak amplitude of 1 mm at a frequency around 1.3 kHz. Based on the experimental results, the power density prediction of the proposed harvester design shows a superior performance than that of the other reported piezoelectric harvesters.

[1]  Aaas News,et al.  Book Reviews , 1893, Buffalo Medical and Surgical Journal.

[2]  S. Farritor,et al.  On low-frequency electric power generation with PZT ceramics , 2005, IEEE/ASME Transactions on Mechatronics.

[3]  Kee S. Moon,et al.  Single crystal piezoelectric transducers to harvest vibration energy , 2005, International Symposium on Optomechatronic Technologies.

[4]  Jingang Yi,et al.  Tire tread deformation sensor and energy harvester development for smart-tire applications , 2007, SPIE Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[5]  Sang-Gook Kim,et al.  Energy harvesting MEMS device based on thin film piezoelectric cantilevers , 2006 .

[6]  N. Jalili,et al.  Modeling, Nonlinear Dynamics, and Identification of a Piezoelectrically Actuated Microcantilever Sensor , 2008, IEEE/ASME Transactions on Mechatronics.

[7]  Neil M. White,et al.  Towards a piezoelectric vibration-powered microgenerator , 2001 .

[8]  Rajeevan Amirtharajah,et al.  Self-powered signal processing using vibration-based power generation , 1998, IEEE J. Solid State Circuits.

[9]  Kee S. Moon,et al.  Single-Crystal Film Piezoelectric Sensors, Actuators and Energy Harvesters with Interdigitated Electrodes , 2006 .

[10]  Sergey Edward Lyshevski,et al.  Micromechatronics: Modeling, Analysis, and Design with MATLAB , 2003 .

[11]  Sang-Gook Kim,et al.  DESIGN CONSIDERATIONS FOR MEMS-SCALE PIEZOELECTRIC MECHANICAL VIBRATION ENERGY HARVESTERS , 2005 .

[12]  T. Shrout,et al.  Ultrahigh strain and piezoelectric behavior in relaxor based ferroelectric single crystals , 1997 .

[13]  T.C. Green,et al.  Architectures for vibration-driven micropower generators , 2004, Journal of Microelectromechanical Systems.

[14]  Y. Shu,et al.  Analysis of power output for piezoelectric energy harvesting systems , 2006 .

[15]  L. G. Jaeger,et al.  Dynamics of structures , 1990 .

[16]  S. Shahruz.  Design of mechanical band-pass filters for energy scavenging , 2006 .

[17]  Sang-Gook Kim,et al.  MEMS power generator with transverse mode thin film PZT , 2005 .

[18]  Shadrach Roundy,et al.  On the Effectiveness of Vibration-based Energy Harvesting , 2005 .

[19]  Henry A. Sodano,et al.  A review of power harvesting using piezoelectric materials (2003–2006) , 2007 .