Electromagnetic interference (EMI) reduction from printed circuit boards (PCB) using electromagnetic bandgap structures

As digital circuits become faster and more powerful, direct radiation from the power bus of their printed circuit boards (PCB) becomes a major concern for electromagnetic compatibility engineers. In such multilayer PCBs, the power and ground planes act as radiating microstrip patch antennas, where radiation is caused by fringing electric fields at board edges. In this paper, we introduce an effective method for suppressing PCB radiation from their power bus over an ultrawide range of frequencies by using metallo-dielectric electromagnetic band-gap structures. More specifically, this study focuses on the suppression of radiation from parallel-plate bus structures in high-speed PCBs caused by switching noise, such as simultaneous switching noise, also known as Delta-I noise or ground bounce. This noise consists of unwanted voltage fluctuations on the power bus of a PCB due to resonance of the parallel-plate waveguiding system created by the power bus planes. The techniques introduced here are not limited to the suppression of switching noise and can be extended to any wave propagation between the plates of the power bus. Laboratory PCB prototypes were fabricated and tested revealing appreciable suppression of radiated noise over specific frequency bands of interest, thus, testifying to the effectiveness of this concept.

[1]  V. Ricchiuti.  Power-supply decoupling on fully populated high-speed digital PCBs , 2001 .

[2]  O.M. Ramahi,et al.  A novel power plane with integrated simultaneous switching noise mitigation capability using high impedance surface , 2003, IEEE Microwave and Wireless Components Letters.

[3]  Stephen H. Hall,et al.  High-Speed Digital System Design: A Handbook of Interconnect Theory and Design Practices , 2000 .

[4]  M. Leone.  The radiation of a rectangular power-bus structure at multiple cavity-mode resonances , 2003 .

[5]  S. Radu,et al.  An investigation of PCB radiated emissions from simultaneous switching noise , 1999, 1999 IEEE International Symposium on Electromagnetic Compatability. Symposium Record (Cat. No.99CH36261).

[6]  Todd H. Hubing,et al.  Reducing power bus impedance at resonance with lossy components , 2001 .

[7]  Y. Rahmat-Samii,et al.  In-phase reflection and EM wave suppression characteristics of electromagnetic band gap ground planes , 2003, IEEE Antennas and Propagation Society International Symposium. Digest. Held in conjunction with: USNC/CNC/URSI North American Radio Sci. Meeting (Cat. No.03CH37450).

[8]  James L. Drewniak,et al.  The EMI benefits of ground plane stitching in multi-layer power bus stacks , 2000, IEEE International Symposium on Electromagnetic Compatibility. Symposium Record (Cat. No.00CH37016).

[9]  George V. Eleftheriades,et al.  Metallo-dielectric electromagnetic bandgap structures for suppression and isolation of the parallel-plate noise in high-speed circuits , 2003 .

[10]  Y. Rahmat-Samii,et al.  Microstrip antennas integrated with electromagnetic band-gap (EBG) structures: a low mutual coupling design for array applications , 2003 .

[11]  Minjia Xu,et al.  MODELING PRINTED CIRCUIT BOARDS WITH EMBEDDED DECOUPLING CAPACITANCE , 2001 .

[12]  Todd H. Hubing.  Printed circuit board EMI source mechanisms , 2003, 2003 IEEE Symposium on Electromagnetic Compatibility. Symposium Record (Cat. No.03CH37446).

[13]  Zhang Jin,et al.  Physics based modeling of simultaneous switching noise in high speed systems , 2000, 2000 Proceedings. 50th Electronic Components and Technology Conference (Cat. No.00CH37070).

[14]  L. Brillouin.  Wave propagation in periodic structures : electric filters and crystal lattices , 1953 .

[15]  Zhang Jin,et al.  Modeling of simultaneous switching noise in high speed systems , 2001, ECTC 2001.

[16]  Xin Wu,et al.  Mitigating multi-layer PCB power bus radiation through novel mesh fencing techniques , 2003, Electrical Performance of Electrical Packaging (IEEE Cat. No. 03TH8710).

[17]  F. Olyslager,et al.  Study of the ground bounce caused by power plane resonances , 1998 .

[18]  E. Yablonovitch,et al.  Eliminating surface currents with metallodielectric photonic crystals , 1998, 1998 IEEE MTT-S International Microwave Symposium Digest (Cat. No.98CH36192).

[19]  John L. Prince,et al.  Simultaneous Switching Noise of CMOS Devices and Systems , 1993 .

[20]  B. Archambeault,et al.  A simple finite-difference frequency-domain (FDFD) algorithm for analysis of switching noise in printed circuit boards and packages , 2003 .

[21]  Omar M. Ramahi,et al.  Simultaneous switching noise mitigation in PCB using cascaded high-impedance surfaces , 2004 .

[22]  I. Novak,et al.  Reducing simultaneous switching noise and EMI on ground/power planes by dissipative edge termination , 1998, IEEE 7th Topical Meeting on Electrical Performance of Electronic Packaging (Cat. No.98TH8370).

[23]  D. Sievenpiper,et al.  High-impedance electromagnetic surfaces with a forbidden frequency band , 1999 .

[24]  Radiation characteristics of microstrip dipole antennas over a high-impedance metamaterial surface made of Hilbert inclusions , 2003, IEEE MTT-S International Microwave Symposium Digest, 2003.

[25]  J. Papapolymerou,et al.  A planar X-band electromagnetic band-gap (EBG) 3-pole filter , 2002, IEEE Microwave and Wireless Components Letters.

[26]  T. Hubing,et al.  Power bus noise reduction using power islands in printed circuit board designs , 1999, 1999 International Symposium on Electromagnetic Compatibility (IEEE Cat. No.99EX147).