Die opening-induced microstructure growth in extrusion foaming of thermoplastic sheets

Abstract In this study, the influence of die opening gap on foam attributes during a microcellular extrusion foaming process was investigated. Lower die openings developed higher pressure drops on the foams, as a result of which greater thermodynamic instability was stimulated and, consequently, higher cell density foams along with enhanced expansion ratios were achieved. Further investigations were performed to study the synergistic influence of altering die opening with critical process parameters, namely, screw rotational speed and die temperature, on the foam expansion ratio and morphological transformations. Higher screw rotational speed induced shear nucleation phenomenon, which further enhanced the foaming process significantly. Also, an optimum die temperature was observed, which developed maximum expansion ratio at the lowest die opening gap. This study intends to enhance the understanding of extrusion foam processing among academia as well as among industries.

[1]  N. Bhatnagar,et al.  Surface Quenching Induced Microstructure Transformations in Extrusion Foaming of Porous Sheets , 2015 .

[2]  R. Mülhaupt,et al.  Influence of graphene on the cell morphology and mechanical properties of extruded polystyrene foam , 2015 .

[3]  Chul B. Park,et al.  Past and present developments in polymer bead foams and bead foaming technology , 2015 .

[4]  Chul B. Park,et al.  Superhydrophobic and oleophilic open-cell foams from fibrillar blends of polypropylene and polytetrafluoroethylene. , 2014, ACS applied materials & interfaces.

[5]  N. Bhatnagar,et al.  Ultrasound‐induced nucleation in microcellular polymers , 2014 .

[6]  Zhongyuan Lu,et al.  Preparation of silicone rubber foam using supercritical carbon dioxide , 2014 .

[7]  B. Kichatov,et al.  An extrusion die with rollers for foaming polymers , 2014 .

[8]  W. Huang,et al.  Thermoplastic polyurethane microcellular fibers via supercritical carbon dioxide based extrusion foaming , 2013 .

[9]  S. Chen,et al.  The effects of gas counter pressure and mold temperature variation on the surface quality and morphology of the microcellular polystyrene foams , 2013 .

[10]  N. Bhatnagar,et al.  Ultrasound assisted cyclic solid-state foaming for fabricating ultra-low density porous acrylonitrile–butadiene–styrene foams , 2013 .

[11]  Chul B. Park,et al.  Effect of nanoclay addition on the foaming behavior of linear polypropylene‐based soft thermoplastic polyolefin foam blown in continuous extrusion , 2011 .

[12]  Chul B. Park,et al.  The effects of nanoclay on the extrusion foaming of wood fiber/polyethylene nanocomposites , 2011 .

[13]  B. D. Favis,et al.  Rheology and extrusion foaming of chain‐branched poly(lactic acid) , 2010 .

[14]  L. Matuana,et al.  Study of Cell Nucleation in Microcellular Poly(lactic acid) Foamed with Supercritical CO2 through a Continuous-Extrusion Process , 2010 .

[15]  Chul B. Park,et al.  Microcellular Extrusion-Foaming of Polylactide with Chain-Extender , 2009 .

[16]  G. Nam,et al.  Relationships between Processing Parameters and the Foaming Performances of Polyethylene for Coaxial Cable Insulation , 2008 .

[17]  Chul B. Park,et al.  Effects of the die geometry on the expansion of polystyrene foams blown with carbon dioxide , 2008 .

[18]  Bin Yang,et al.  Investigation of sorption and diffusion of supercritical carbon dioxide in polycarbonate , 2008 .

[19]  M. Mihai,et al.  Extrusion foaming of semi-crystalline PLA and PLA/thermoplastic starch blends. , 2007, Macromolecular bioscience.

[20]  Sunghak Lee,et al.  Corrosion resistance of steel-based surface alloyed materials fabricated with Fe-based metamorphic powders by high-energy electron beam irradiation , 2006 .

[21]  Chul B. Park,et al.  Extrusion of microcellular open‐cell LDPE‐based sheet foams , 2006 .

[22]  Chul B. Park,et al.  Challenge to Extrusion of Low-Density Microcellular Polycarbonate Foams Using Supercritical Carbon Dioxide , 2005 .

[23]  C. Macosko,et al.  Strain hardening in polypropylenes and its role in extrusion foaming , 2004 .

[24]  M. Guo,et al.  Study of shear nucleation theory in continuous microcellular foam extrusion , 2003 .

[25]  L. Matuana,et al.  Foam extrusion of high density polyethylene/wood-flour composites using chemical foaming agents , 2003 .

[26]  L. J. Lee,et al.  Effect of die temperature on the morphology of microcellular foams , 2003 .

[27]  Xiang Wang,et al.  Shear stress nucleation in microcellular foaming process , 2002 .

[28]  Chul B. Park,et al.  An extrusion system for the processing of microcellular polymer sheets: Shaping and cell growth control , 1996 .

[29]  Chul B. Park,et al.  Filamentary extrusion of microcellular polymers using a rapid decompressive element , 1996 .

[30]  Chul B. Park,et al.  Effect of the pressure drop rate on cell nucleation in continuous processing of microcellular polymers , 1995 .

[31]  Shau‐Tarng Lee,et al.  Shear effects on thermoplastic foam nucleation , 1993 .