Intermetallics Characterization of Lead-Free Solder Joints under Isothermal Aging

Solder interconnect reliability is influenced by environmentally imposed loads, solder material properties, and the intermetallics formed within the solder and the metal surfaces to which the solder is bonded. Several lead-free metallurgies are being used for component terminal plating, board pad plating, and solder materials. These metallurgies react together and form intermetallic compounds (IMCs) that affect the metallurgical bond strength and the reliability of solder joint connections. This study evaluates the composition and extent of intermetallic growth in solder joints of ball grid array components for several printed circuit board pad finishes and solder materials. Intermetallic growth during solid state aging at 100°C and 125°C up to 1000 h for two solder alloys, Sn-3.5Ag and Sn-3.0Ag-0.5Cu, was investigated. For Sn-3.5Ag solder, the electroless nickel immersion gold (ENIG) pad finish was found to result in the lowest IMC thickness compared to immersion tin (ImSn), immersion silver (ImAg), and organic solderability preservative (OSP). Due to the brittle nature of the IMC, a lower IMC thickness is generally preferred for optimal solder joint reliability. A lower IMC thickness may make ENIG a desirable finish for long-life applications. Activation energies of IMC growth in solid-state aging were found to be 0.54 ± 0.1 eV for ENIG, 0.91 ± 0.12 eV for ImSn, and 1.03 ± 0.1 eV for ImAg. Cu3Sn and Cu6Sn5 IMCs were found between the solder and the copper pad on boards with the ImSn and ImAg pad finishes. Ternary (Cu,Ni)6Sn5 intermetallics were found for the ENIG pad finish on the board side. On the component side, a ternary IMC layer composed of Ni-Cu-Sn was found. Along with intermetallics, microvoids were observed at the interface between the copper pad and solder, which presents some concern if devices are subject to shock and vibration loading.

[1]  Michael Pecht,et al.  Lead-free Electronics , 2006 .

[2]  J. Kivilahti,et al.  Solder/Substrate Interfacial Reactions in the Sn-Cu-Ni Interconnection System , 2007 .

[3]  T.H. Low,et al.  Isothermal and thermal cycling aging on IMC growth rate in lead-free and lead-based solder interface , 2005, IEEE Transactions on Components and Packaging Technologies.

[4]  Richard J. Coyle,et al.  The effect of modifications to the nickel/gold surface finish on assembly quality and attachment reliability of a plastic ball grid array (peer review version) , 2003 .

[5]  Michael Pecht,et al.  Evaluation of selected Japanese lead-free consumer electronics , 2003 .

[6]  S. Ganesan,et al.  Using cut-out features for efficient printed circuit board testing and failure analysis , 2005, IEEE Transactions on Components and Packaging Technologies.

[7]  Richard Ciocci,et al.  Questions concerning the migration to lead‐free solder , 2004 .

[8]  S. Rajagopal,et al.  The impact of lead-free legislation exemptions on the electronics industry , 2004, IEEE Transactions on Electronics Packaging Manufacturing.

[9]  D. R. Frear,et al.  Morphology, kinetics, and thermodynamics of solid-state aging of eutectic SnPb and Pb-free solders (Sn–3.5Ag, Sn–3.8Ag–0.7Cu and Sn–0.7Cu) on Cu , 2002 .

[10]  Michael Pecht,et al.  Lead-free soldering in the Japanese electronics industry , 2003 .

[11]  G. Li,et al.  Formation and growth kinetics of interfacial intermetallics in Pb-free solder joint , 2003 .