Study on Machinabilty of Al2O3 Ceramic Composite in EDM Using Response Surface Methodology

Electric discharge machining (EDM) has been proven as an alternate process for machining complex and intricate shapes from the conductive ceramic composites. Al 2 O 3 based electrodischarge machinable Al 2 O 3 ―SiC w ―TiC ceramic composite is a potential substitute for traditional materials due to their high hardness, excellent chemical, and mechanical stability under a broad range of temperature, and high specific stiffness. The right selection of the machining condition is the most important aspect to take into consideration in the EDM. The present work correlates the inter-relationships of various EDM machining parameters, namely, discharge current, pulse-on time, duty cycle, and gap voltage on the metal removal rate (MRR), electrode wear ratio (EWR), and surface roughness using the response surface methodology (RSM) while EDM of Al 2 O 3 ―SiC w ―TiC ceramic composite. Analysis of variance is used to study the significance of process variables on MRR, EWR, and surface roughness. The experimental results reveal that discharge current, pulse-on time, and duty cycle significantly affected MRR and EWR, while discharge current and pulse-on time affected the surface roughness. The validation of developed models shows that the MRR EWR and surface roughness of EDM of Al 2 O 3 ―SiC w ―TiC ceramic can be estimated with reasonable accuracy using the second-order models. Finally, trust-region method for nonlinear minimization is used to find the optimum levels of the parameters. The surface and subsurface damage have also been assessed and characterized using scanning electron microscopy. This study reveals that EDMed material unevenness increases with discharge current and pulse-on time.

[1]  B. I. Smirnov,et al.  Mechanical properties and microstructure of an Al2O3–SiC–TiC composite , 1998 .

[2]  B. Yan,et al.  Improvement of surface finish on SKD steel using electro-discharge machining with aluminum and surfactant added dielectric , 2005 .

[3]  Tai-chiu Lee,et al.  Study on the electro-discharge machining of a hot pressed aluminum oxide based ceramic , 1997 .

[4]  C. Çoğun,et al.  An experimental investigation of tool wear in electric discharge machining , 2006 .

[5]  J. Huddleston,et al.  Production and EDM of Si3 N4–TiB2 ceramic composites , 2001 .

[6]  Said Jahanmir,et al.  Material removal and damage formation mechanisms in grinding silicon nitride , 1996 .

[7]  Margaret J. Robertson,et al.  Design and Analysis of Experiments , 2006, Handbook of statistics.

[8]  B. Bhattacharyya,et al.  Parametric analysis on electrochemical discharge machining of silicon nitride ceramics , 2006 .

[9]  E. Oshima,et al.  Investigation on the Optimum Carbide Content and Machining Condition for Wire EDM of Zirconia Ceramics , 1992 .

[10]  S. M. Mahdavian,et al.  Parametric study into erosion wear in a computer numerical controlled electro-discharge machining process , 1999 .

[11]  A. Pitman,et al.  Electrical discharge machining of ZrO2 /TiN particulate composite , 2000 .

[12]  A. Pitman,et al.  Electrical discharge machining of ZrO 2 /TiN particulate composite , 2000 .

[13]  I. R. Pashby,et al.  Review: Various methods of machining advanced ceramic materials , 1994 .

[14]  Ko-Ta Chiang,et al.  Modeling and analysis of the effects of machining parameters on the performance characteristics in the EDM process of Al2O3+TiC mixed ceramic , 2008 .

[15]  L. Hwang,et al.  Machining Characteristics and Optimization of Machining Parameters of SKH 57 High-Speed Steel Using Electrical-Discharge Machining Based on Taguchi Method , 2006 .

[16]  J. Vleugels,et al.  Die sink electrodischarge machining of zirconia based composites , 2001 .

[17]  Ko-Ta Chiang,et al.  Applying grey forecasting method for fitting and predicting the performance characteristics of an electro-conductive ceramic (Al2O3+30%TiC) during electrical discharge machining , 2007 .

[18]  Yukio Hirai,et al.  Surface damage in ZrB2-based composite ceramics induced by electro-discharge machining , 1991 .

[19]  Fu Chen-Tsu,et al.  The dependence of surface damage induced by electrical-discharge machining on the fracture strength of Al2O3−Cr3C2 composites , 1994 .