Thermal performance in solar air heater with perforated-winglet-type vortex generator

Abstract An experimental and numerical study of turbulent convective heat transfer in a solar air heater duct with winglet-type vortex generators (WVGs) placed on the absorber plate is presented. Air as the test fluid enters the duct having a uniform wall heat-flux applied on the upper wall or the absorber plate with Reynolds number from 4100 to 25,500. Two types of WVGs are introduced: rectangular (RWVG) and trapezoidal (TWVG) WVGs, in order to create multiple vortex flows along the duct. The WVG parameters in the present study include two relative height (BR = e/H = 0.2 and 0.48), three longitudinal pitch ratios (PR = Pl/H = 1, 1.5 and 2) and a single attack angle, α = 30°. The experimental result reveals that the RWVG with BR = 0.48 and PR = 1 provides the highest heat transfer and friction factor at about 7.1 and 109.5 times above the flat duct, respectively while the TWVG with BR = 0.2 and PR = 1.5 yields the maximum thermal performance around 1.84. Then, to improve the performance by reducing the substantial pressure loss, both the WVGs with BR = 0.48 and PR = 1.5 are modified to be perforated rectangular and trapezoidal winglet-type vortex generators (P-RWVG and P-TWVG) with four different punched hole/pore diameters (d = 1, 3, 5 and 7 mm) on their central area. The investigation indicates that among the perforated WVGs, the P-RWVG at d = 1 mm yields the highest heat transfer and friction factor up to 6.78 and 84.32 times higher than the smooth duct but the best thermal performance of about 2.01 is found for the P-TWVG with d = 5 mm. To explore the flow and heat transfer pattern, a 3D numerical flow simulation is performed and validated with available measurements where both the numerical and measured results are in good agreement.

[1]  J. Yanagihara,et al.  Interaction effects between parameters in a flat-tube louvered fin compact heat exchanger with delta-winglets vortex generators , 2015 .

[2]  Pongjet Promvonge,et al.  Thermal characterization of turbulent flow in a channel with isosceles triangular ribs , 2009 .

[3]  V. Zimparov,et al.  Extended performance evaluation criteria for enhanced heat transfer surfaces: heat transfer through ducts with constant heat flux , 2001 .

[4]  P. Promvonge,et al.  Effects of rib size and arrangement on forced convective heat transfer in a solar air heater channel , 2015 .

[5]  Pongjet Promvonge,et al.  Numerical heat transfer study of turbulent square-duct flow through inline V-shaped discrete ribs , 2011 .

[6]  K. Srithar,et al.  Comprehensive study on solar air heater with circular and V-type turbulators attached on absorber plate , 2015 .

[7]  Giovanni Tanda,et al.  Heat transfer in rectangular channels with transverse and V-shaped broken ribs , 2004 .

[8]  Pongjet Promvonge,et al.  Thermal performance enhancement in a heat exchanger tube fitted with inclined vortex rings , 2014 .

[9]  K. N. Sheeba,et al.  Studies on heat transfer and friction factor characteristics of thermosyphon solar water heating system with helical twisted tapes , 2009 .

[10]  Pongjet Promvonge,et al.  Experimental investigation of heat transfer and flow friction in a circular tube fitted with regularly spaced twisted tape elements , 2006 .

[11]  Guobing Zhou,et al.  Experimental investigations of thermal and flow characteristics of curved trapezoidal winglet type vortex generators , 2012 .

[12]  Sang woo Lee,et al.  Tip leakage aerodynamics over the cavity squealer tip equipped with full coverage winglets in a turbine cascade , 2015 .

[13]  Ralph L. Webb,et al.  Performance evaluation criteria for use of enhanced heat transfer surfaces in heat exchanger design , 1981 .

[14]  P. Promvonge,et al.  Heat transfer augmentation in a solar air heater channel with combined winglets and wavy grooves on absorber plate , 2017 .

[15]  Varun,et al.  A thermodynamic review of solar air heaters , 2015 .

[16]  Guobing Zhou,et al.  Experimental investigations of heat transfer enhancement by plane and curved winglet type vortex generators with punched holes , 2014 .

[17]  P. Promvonge,et al.  Thermal performance assessment of turbulent channel flows over different shaped ribs , 2008 .

[18]  A. S. Dhoble,et al.  Effect of roughness geometries on heat transfer enhancement in solar thermal systems – A review , 2014 .

[19]  Pongjet Promvonge,et al.  Experimental Investigation on Turbulent Convection in Solar Air Heater Channel Fitted with Delta Winglet Vortex Generator , 2014 .

[20]  S. Canbazoğlu,et al.  Performance and flow-induced vibration characteristics for conical-ring turbulators , 2004 .

[21]  Pongjet Promvonge,et al.  Enhanced heat transfer in a triangular ribbed channel with longitudinal vortex generators , 2010 .

[22]  Pongjet Promvonge,et al.  Thermal enhancement in a round tube with snail entry and coiled-wire inserts , 2008 .

[23]  Pongjet Promvonge,et al.  Thermal performance in solar air heater channel with combined wavy-groove and perforated-delta wing vortex generators , 2016 .

[24]  Pongjet Promvonge,et al.  Heat transfer augmentation in a wedge-ribbed channel using winglet vortex generators , 2010 .

[25]  Pongjet Promvonge,et al.  Numerical study of laminar flow and heat transfer in square channel with 30° inline angled baffle turbulators , 2010 .

[26]  Pongjet Promvonge,et al.  Heat transfer behaviors in a solar air heater channel with multiple V-baffle vortex generators , 2014 .

[27]  Frank P. Incropera,et al.  Foundations of heat transfer , 2013 .

[29]  S. Patankar.  Numerical Heat Transfer and Fluid Flow , 2018, Lecture Notes in Mechanical Engineering.

[30]  Anthony M. Jacobi,et al.  Heat transfer enhancement by winglet-type vortex generator arrays in compact plain-fin-and-tube heat exchangers , 2008 .

[31]  R. P. Saini,et al.  Effect of circularity of perforation holes in V-shaped blockages on heat transfer and friction characteristics of rectangular solar air heater duct , 2014 .

[32]  Varun,et al.  Heat transfer and friction factor correlations for multiple arc shape roughness elements on the absorber plate used in solar air heaters , 2014 .

[33]  Pongjet Promvonge,et al.  Experimental and numerical study on heat transfer enhancement in a channel with Z-shaped baffles ☆ , 2012 .

[34]  Anthony M. Jacobi,et al.  Heat transfer enhancement by delta-wing vortex generators on a flat plate: Vortex interactions with the boundary layer , 1997 .

[35]  Pongjet Promvonge,et al.  Thermal behavior in solar air heater channel fitted with combined rib and delta-winglet ☆ , 2011 .

[36]  S. C. Solanki,et al.  Heat transfer and friction in solar air heater duct with V-shaped rib roughness on absorber plate , 2002 .

[37]  Varun,et al.  Experimental investigation of heat transfer augmentation using multiple arcs with gap on absorber plate of solar air heater , 2016 .

[38]  J. Saini,et al.  Experimental investigation on heat-transfer enhancement due to a gap in an inclined continuous rib arrangement in a rectangular duct of solar air heater , 2008 .

[39]  Pongjet Promvonge,et al.  Heat transfer and pressure drop in a channel with multiple 60° V-baffles ☆ , 2010 .

[40]  P. Promvonge,et al.  Experimental and numerical heat transfer investigation in turbulent square-duct flow through oblique horseshoe baffles , 2016 .

[41]  E. Sparrow,et al.  Fully Developed Flow and Heat Transfer in Ducts Having Streamwise-Periodic Variations of Cross-Sectional Area , 1977 .

[42]  J. Yanagihara,et al.  Heat transfer enhancement and optimization of flat-tube multilouvered fin compact heat exchangers with delta-winglet vortex generators , 2016 .