Parametric Study on the Geometric and Kinetic Aspects of the Slider-Crank Mechanism

[1]  M. Večeř,et al.  Fundamentals of the fluid mechanics , 2020 .

[2]  Iman Fattahi,et al.  Novel composite finite element model for piezoelectric energy harvesters based on 3D beam kinematics , 2017 .

[3]  Saeed Ziaei-Rad,et al.  Improving the read/write performance of hard disk drives under external excitation sources based on multi-objective optimization , 2017 .

[4]  Saeed Ziaei-Rad,et al.  A new approach to design safe-supported HDD against random excitation by using optimization of rubbers spatial parameters , 2017 .

[5]  Samin Akbari,et al.  Dynamic analysis and controller design for a slider-crank mechanism with piezoelectric actuators , 2016, J. Comput. Des. Eng..

[6]  S. Ziaei-Rad,et al.  Improving the read/write performance of hard disk drives under external excitation sources based on multi-objective optimization , 2016, Microsystem Technologies.

[7]  Lin Han,et al.  Dynamic analysis of a slider-crank mechanism with two types of non-ideal revolute joints , 2015 .

[8]  S. M. Varedi,et al.  Optimal dynamic design of a planar slider-crank mechanism with a joint clearance , 2015 .

[9]  Katia Lucchesi Cavalca,et al.  Dynamic analysis of a lubricated planar slider–crank mechanism considering friction and Hertz contact effects , 2014 .

[10]  Xinlong Zhou,et al.  Modeling and simulation of flexible slider-crank mechanism with clearance for a closed high speed press system , 2014 .

[11]  D P Naik,et al.  Planar Slider - crank mechanism adjustable for prescribed dead - center positions , 2013 .

[12]  Kyu-Jin Cho,et al.  Design of a slider-crank leg mechanism for mobile hopping robotic platforms , 2013 .

[13]  Han Yongjie,et al.  General Design Method of Flywheel Rotor for Energy Storage System , 2012 .

[14]  Engin Tanık,et al.  Transmission angle in compliant slider-crank mechanism , 2011 .

[15]  Katia Lucchesi Cavalca,et al.  Analysis of the dynamics of a slider–crank mechanism with hydrodynamic lubrication in the connecting rod–slider joint clearance , 2011 .

[16]  Mansour Rasekh,et al.  Kinematics and Kinetic Analysis of the Slider-Crank Mechanism in Otto Linear Four Cylinder Samand Engine , 2011 .

[17]  Selçuk Erkaya,et al.  Experimental investigation of joint clearance effects on the dynamics of a slider-crank mechanism , 2010 .

[18]  Rong-Fong Fung,et al.  Dynamic modelling of an intermittent slider–crank mechanism , 2009 .

[19]  Selçuk Erkaya,et al.  Optimization of transmission angle for slider-crank mechanism with joint clearances , 2009 .

[20]  Lotfi Romdhane,et al.  Dynamic analysis of a flexible slider-crank mechanism with clearance , 2008 .

[21]  Daniel J. Inman,et al.  Engineering Mechanics: Dynamics , 1966 .

[22]  Hans Bernhoff,et al.  Flywheel energy and power storage systems , 2007 .

[23]  Jorge Ambrósio,et al.  A study on dynamics of mechanical systems including joints with clearance and lubrication , 2006 .

[24]  Rong-Fong Fung,et al.  Dynamic modeling and identification of a slider-crank mechanism , 2006 .

[25]  Jehad A. A. Yamin,et al.  Performance simulation of a four-stroke engine with variable stroke-length and compression ratio , 2004 .

[26]  Kenan Koser,et al.  A slider crank mechanism based robot arm performance and dynamic analysis , 2004 .

[27]  Kwun-Lon Ting,et al.  Adjustable slider–crank linkages for multiple path generation , 2002 .

[28]  Eres Söylemez,et al.  Classical transmission-angle problem for slider–crank mechanisms , 2002 .

[29]  Satish Chand,et al.  Transmission angle in mechanisms (Triangle in mech) , 2002 .

[30]  Jen-San Chen,et al.  DYNAMIC ANALYSIS OF FLEXIBLE SLIDER-CRANK MECHANISMS WITH NON-LINEAR FINITE ELEMENT METHOD , 2001 .

[31]  Livija Cveticanin,et al.  Dynamic analysis of a cutting mechanism , 2000 .

[32]  R.-F. Fung,et al.  DYNAMIC ANALYSIS AND VIBRATION CONTROL OF A FLEXIBLE SLIDER–CRANK MECHANISM USING PM SYNCHRONOUS SERVO MOTOR DRIVE , 1998 .

[33]  Bernd Simeon,et al.  Modelling a flexible slider crank mechanism by a mixed system of DAEs and PDEs , 1996 .

[34]  B. Fallahi,et al.  A Finite Element Formulation of a Flexible Slider Crank Mechanism Using Local Coordinates , 1994 .

[35]  S. Shaw,et al.  Chaotic and periodic dynamics of a slider-crank mechanism with slider clearance , 1994 .

[36]  Steven W. Shaw,et al.  The Dynamic Stability and Non-Linear Resonance of a Flexible Connecting Rod: Single-Mode Model , 1994 .

[37]  J. T. Kimbrell,et al.  Kinematics Analysis and Synthesis , 1991 .

[38]  Brian S. Thompson,et al.  A Theoretical and Experimental Investigation of the Dynamic Response of a Slider-Crank Mechanism With Radial Clearance in the Gudgeon-Pin Joint , 1990 .

[39]  A. Myklebust,et al.  Dynamic Response of Slider-Crank Machines During Startup , 1984 .

[40]  Terry E. Shoup,et al.  The design of an adjustable, three dimensional slider crank mechanism , 1984 .

[41]  A. Midha,et al.  Effect of Internal Material Damping on the Dynamics of a Slider-Crank Mechanism , 1983 .

[42]  Kenneth J. Waldron,et al.  Graphical transmission angle control in planar linkage synthesis , 1981 .

[43]  J. N Fawcett,et al.  Dynamics of the slider-crank mechanism with clearance in the sliding bearing , 1974 .

[44]  Joseph Edward Shigley,et al.  Mechanical engineering design , 1972 .

[45]  A. P,et al.  Mechanical Vibrations , 1948, Nature.