Gradient-distributed ZTAp-VCp/Fe45 as new anti-wear composite material and its bonding properties during composite casting

Abstract In this article, gradient-distributed VCp-ZTAp/Fe45 composites were prepared by vacuum sintering, and three-body abrasive wear experiments were carried out to investigate its anti-wear performance. The composite casting of VCp-ZTAp/Fe45 was investigated by using the finite element method and experiments, and the bonding between the Fe45 substrate and 35SiMnCrMoNi steel was fully investigated. Results show the in situ formation of VCp in the VCp-ZTAp/Fe45 composite matrix during vacuum sintering. The anti-wear property of the VCp-ZTAp/Fe45 composite is ca. 7 times that of Hardox450 and NM450 and ca. 8 times of 30SiMn. There forms a solid metallurgical bonding between the Fe45 matrix of VCp-ZTAp/Fe45 and 35SiMnCrMoNi steel, with a ca. 80 μm thickness of the bonding area during the composite casting.

[1]  L. Arnberg,et al.  Achieving high-strength metallurgical bonding between A356 aluminum and copper through compound casting , 2021 .

[2]  He-bao Wu,et al.  Improved interface bonding of Mg/aluminized steel bimetallic castings prepared by solid–liquid compound casting process , 2020, International Journal of Cast Metals Research.

[3]  Yang Qin,et al.  Behaviors of ZTA (zirconia toughened alumina) reinforced iron composites under impact abrasive wear conditions , 2020 .

[4]  Qiu Xu,et al.  Research status and development trend of preparation technology of ceramic particle dispersion strengthened copper-matrix composites , 2020 .

[5]  Jing Shi,et al.  Microstructure and mechanical properties of Fe matrix composites reinforced by nickel–chromium double-layer coated ZTAP ceramics , 2020 .

[6]  Ping Li,et al.  Effects of manganese on diffusion and wear behavior of ZTA particles reinforced iron matrix composites in vacuum , 2020 .

[7]  J. Arasteh,et al.  Microstructural evolution during high-energy mechanical alloying of immiscible Zr–Cr alloy , 2020, Journal of Materials Research.

[8]  Yunhua Xu,et al.  Microstructure and compressive properties of V–V8C7/Fe core-shell rod-reinforced iron-based composite fabricated via two-step in-situ reaction , 2020 .

[9]  E. Feldshtein,et al.  Tribological Properties of Iron-Based Powder Composite Materials with Addition of Graphite, Alumina and Zirconia Nanoparticles , 2020, Journal of Friction and Wear.

[10]  E. Feldshtein,et al.  Wear minimization for highly loaded iron-based MMCs due to the formation of spongy-capillary texture on the friction surface , 2020 .

[11]  You-wen Yang,et al.  Numerical simulation and optimization of shell mould casting process for leaf spring bracket , 2020, China Foundry.

[12]  Wei Li,et al.  Effect of ZTA ceramic particles strengthened high chromium white cast iron on three-body abrasion behavior , 2019, Materials Research Express.

[13]  Yunhua Xu,et al.  Evaluation of growth behaviour of vanadium carbides-reinforced iron-based surface compound layer by in-situ reaction , 2019, Vacuum.

[14]  Jian-xun Fu,et al.  The effect of Al content on the wettability between liquid iron and MgO Al2O3 binary substrate , 2019, Ceramics International.

[15]  Xin Jin,et al.  Microstructure and Tribological Properties of WC Reinforced Iron-based Hardfacing Alloy , 2019, IOP Conference Series: Materials Science and Engineering.

[16]  Juanjian Ru,et al.  Ionic Liquid‐Assisted Preparation of Ni–Cr Dual Wrapped ZTA Particles for Reinforced Iron‐Based Composites , 2019, Advanced Engineering Materials.

[17]  Y. Sui,et al.  Microstructure and properties of interfacial transition zone in ZTA particle–reinforced iron composites , 2019, Applied Physics A.

[18]  V. Bolobov,et al.  Influence of Thermomechanical Treatment Modes on Wear Resistance of Mining Equipment Material , 2019, Materials Science Forum.

[19]  Sudhir Kumar,et al.  Experimental Investigation and Evaluation of Joint Strength of A356/Mg Bimetallic Fabricated Using Compound Casting Process , 2018, International Journal of Metalcasting.

[20]  M. Abbasi,et al.  Simulation of casting process: case study on the gating and feeding design for outlet diaphragms of iron ore ball mill , 2018, Heat and Mass Transfer.

[21]  H. Hong,et al.  Preparation of nickel coating on ZTA particles by electroless plating , 2018, Ceramics International.

[22]  Jia Fu,et al.  Design and Improvement of the Investment Casting Process for the Ring-shaped Aluminum Alloy based on PROCAST software , 2018, IOP Conference Series: Materials Science and Engineering.

[23]  Jenn‐Ming Yang,et al.  In situ formation of TiC-particle-reinforced stainless steel matrix nanocomposites during ball milling: Feedstock powder preparation for selective laser melting at various energy densities , 2018 .

[24]  Han Wang,et al.  Numerical simulation and experimental investigation of a thin-wall magnesium alloy casting based on a rapid prototyping core making method , 2018 .

[25]  Kenneth Holmberg,et al.  Global energy consumption due to friction and wear in the mining industry , 2017 .

[26]  A. Roberts,et al.  Abrasion wear resistance of wall lining materials in bins and chutes during iron ore mining , 2017 .

[27]  Zhencai Zhu,et al.  Case study: Wear analysis of the middle plate of a heavy-load scraper conveyor chute under a range of operating conditions , 2017 .

[28]  Bo Liao,et al.  Simulation study on the centrifugal casting wet-type cylinder liner based on ProCAST , 2014 .

[29]  Jing Wang,et al.  Production of in situ Vanadium Carbide Particulate Reinforced Iron Matrix Composite , 2014 .

[30]  A. Gerlich,et al.  Fabrication of metal matrix composites by friction stir processing with different Particles and processing parameters , 2014 .

[31]  Lihua Zou,et al.  Effect of VC Content on Microstructure and Mechanical Properties of VC/Fe-Based Composites , 2012 .

[32]  Dianzhong Li,et al.  Shrinkage porosity criteria and optimized design of a 100-ton 30Cr2Ni4MoV forging ingot , 2012 .

[33]  A. Doering,et al.  Evaluation of ASTM G65 abrasive —Spanning 13 years of sand , 2011 .

[34]  J. Gerring.  A case study , 2011, Technology and Society.

[35]  K. Feng,et al.  Combustion synthesis of VC/Fe composites under the action of an electric field , 2009 .

[36]  P. Weisbecker,et al.  Search for new materials in sputtered V1−xCx films , 2004 .

[37]  K. Aravindh,et al.  Casting design and simulation of gating system in rotary adaptor using procast software for defect minimization , 2020 .

[38]  W. Sun,et al.  Effect of TiC Particles Concentration on Microstructure and Properties of Ni-TiC Composite Coatings , 2019, Materials Research.

[39]  U. K. Vates,et al.  Powder Metallurgy Processing and Mechanical Characterization of Iron-Based Composite Reinforced with Alumina and Zirconium Diboride , 2019, Lecture Notes in Mechanical Engineering.

[40]  P. Lan,et al.  Study on the mechanical behaviors of grey iron mould by simulation and experiment , 2014 .

[41]  T. N. Croft,et al.  Complex free surface flows in centrifugal casting: Computational modelling and validation experiments , 2013 .