Performance analysis of aircraft fuel tank inerting system with turbocharger

The onboard inert gas generation system with turbocharger (OBIGGSTC) was proposed for better inerting performance of an aircraft fuel tank. The operating principle and method of the system were introduced, and the mathematical model of the major component was deduced. Then, the characteristic of the system was simulated based on the software AMESim. Compared with the traditional onboard inert gas generation system (OBIGGS), the proposed system has the potential advantages of reducing the weight and volume of the air separation system by decreasing the number of hollow fiber membrane modules (HFMMs) from a maximum number of eight to one at 0.3 MPa of the bleed air from the engine. When both inerting systems have a single HFMM configuration, the OBIGGSTC can substantially reduce the inerting time by 66.6% compared with the OBIGGS at 0.3 MPa of the bleed air. Due to the turbine applied, the mass flow rate of the bleed air of the inerting system with turbine is greater than the traditional system. The compensatory loss of the proposed system is less than the OBIGGS by a maximum of 57.39% when the bleed air pressure varies from 0.3 to 0.8 MPa with a range in flight time from 4 h to 10 h. By analyzing the two inerting system, the OBIGGSTC has better performance than the OBIGGS.

[1]  Steven M. Summer.  Limiting Oxygen Concentration Required to Inert Jet Fuel Vapors Existing at Reduced Fuel Tank , 2003 .

[2]  E E Wilson,et al.  Aircraft Engine Design , 1925 .

[3]  C. Lawson,et al.  Analytical investigation into the effects of nitrogen enriched air bubbles to improve aircraft fuel system water management , 2019 .

[4]  Zdobysław Goraj.  Design and Optimisation of Fuel Tanks for BWB Configurations , 2016 .

[5]  William H. Heiser,et al.  Aircraft Engine Design, Second Edition , 2003 .

[6]  Lin Guiping,et al.  Experimental study on ceramic membrane technology for onboard oxygen generation , 2016 .

[7]  William M. Cavage,et al.  Modeling In-Flight Inert Gas Distribution in a 747 Center Wing Fuel Tank , 2005 .

[8]  L. Weihua,et al.  Flow rate of nitrogen-rich air and influence factors for onboard air separation unit , 2015 .

[9]  William M. Cavage.  The Effect of Fuel on an Inert Ullage in a Commercial Transport Airplane Fuel Tank , 2005 .

[10]  Richard Hill,et al.  Flight-Testing of the FAA Onboard Inert Gas Generation System on an Airbus A320 , 2004 .

[11]  Liu Suyan.  Separation performance of hollow fiber membrane for on-board inerting gas generating system , 2012 .

[12]  Yang Pei,et al.  Method for analyzing the effect of projectile impact on aircraft fuel tank inerting for survivability design , 2016 .

[13]  Josef Kallo,et al.  Multifunctional fuel cell system in an aircraft environment: An investigation focusing on fuel tank inerting and water generation , 2013 .

[14]  Ray Cherry,et al.  A Benefit Analysis for Nitrogen Inerting of Aircraft Fuel Tanks Against Ground Fire Explosion. , 1999 .

[15]  Craig Lawson,et al.  Behaviour of water in jet fuel - A literature review , 2013 .

[16]  I. Sochet,et al.  Flammability of kerosene in civil and military aviation , 2002 .

[17]  Philip E. Jones,et al.  Aircraft Fuel Systems , 2009 .

[18]  M. Baer,et al.  A Combustion Model for the TWA 800 Center-Wing Fuel Tank Explosion , 1998 .

[19]  Josef Kallo,et al.  Fuel cells for civil aircraft application: On-board production of power, water and inert gas , 2012 .

[20]  Feng Shiyu.  Experimental Study on Separation Performance of Hollow Fiber Membrane for Onboard Inert Gas Generating System , 2011 .

[21]  Michael Burns,et al.  Inerting of a Vented Aircraft Fuel Tank Test Article with Nitrogen-Enriched Air , 2001 .