High-performance polymer solar cells with solution-processed and environmentally friendly CuOx anode buffer layer.

Highly efficient polymer solar cells (PSCs) are demonstrated by introducing environmentally friendly CuOx as hole extraction anode buffer layer. The CuOx buffer layer is prepared simply via spin-coating 1,2-dichlorobenzene solution of Copper acetylacetonate on the ITO substrate and thermal transformation (at 80 °C) in air. Remarkable improvements in the open-circuit voltage (Voc) and short-circuit current density (Jsc) of the PSCs could be achieved upon the introduction of CuOx buffer layer. The study about the effect of CuOx interfacial layer on the device resistances demonstrates that insertion of CuOx layer can decrease the whole resistance of the PSCs. For the devices based on P3HT:PCBM, the power conversion efficiency (PCE) was increased from 2.8% (the reference device without buffer layer) to 4.1% via introduction of CuOx hole extraction layer. The PCE of the PSC was further increased to 6.72% when ICBA used as an alternative acceptor to PCBM. The much higher PCE of 7.14% can be achieved by adopting PBDTTT-C, a low band gap conjugated polymer, as donor material. The results demonstrate that CuOx has great potential as a hole extraction material for highly efficient PSCs.

[1]  Yongfang Li,et al.  Highly Efficient and Thermally Stable Polymer Solar Cells with Dihydronaphthyl‐Based [70]Fullerene Bisadduct Derivative as the Acceptor , 2012 .

[2]  Yongfang Li,et al.  Efficient and stable polymer solar cells with solution-processed molybdenum oxide interfacial layer , 2013 .

[3]  Martijn Kemerink,et al.  Conductivity, work function, and environmental stability of PEDOT:PSS thin films treated with sorbitol , 2008 .

[4]  K. Musselman,et al.  Novel Atmospheric Growth Technique to Improve Both Light Absorption and Charge Collection in ZnO/Cu2O Thin Film Solar Cells , 2013 .

[5]  Gang Li,et al.  Synthesis of a low band gap polymer and its application in highly efficient polymer solar cells. , 2009, Journal of the American Chemical Society.

[6]  N. S. Sariciftci,et al.  Conjugated polymer-based organic solar cells. , 2007, Chemical reviews.

[7]  R. Friend,et al.  Built-in field electroabsorption spectroscopy of polymer light-emitting diodes incorporating a doped poly(3,4-ethylene dioxythiophene) hole injection layer , 1999 .

[8]  Feng Xu,et al.  Replacing alkoxy groups with alkylthienyl groups: a feasible approach to improve the properties of photovoltaic polymers. , 2011, Angewandte Chemie.

[9]  S. E. San,et al.  CdO/Cu2O solar cells by chemical deposition , 2004 .

[10]  A. Kahn,et al.  Charge generation layers comprising transition metal-oxide/organic interfaces: Electronic structure and charge generation mechanism , 2010 .

[11]  M. Ko,et al.  Solution processed WO3 layer for the replacement of PEDOT:PSS layer in organic photovoltaic cells , 2012 .

[12]  Thuc-Quyen Nguyen,et al.  Morphology and conductivity modification of poly(3,4-ethylenedioxythiophene):poly(styrene sulfonate) films induced by conductive atomic force microscopy measurements , 2008 .

[13]  L. Tjeng,et al.  Electronic structure of Cu2O and CuO. , 1988, Physical review. B, Condensed matter.

[14]  Yongfang Li,et al.  High‐Performance Inverted Polymer Solar Cells with Solution‐Processed Titanium Chelate as Electron‐Collecting Layer on ITO Electrode , 2012, Advanced materials.

[15]  Christoph J. Brabec,et al.  Design Rules for Donors in Bulk‐Heterojunction Solar Cells—Towards 10 % Energy‐Conversion Efficiency , 2006 .

[16]  S. Kirchmeyer,et al.  Scientific importance, properties and growing applications of poly(3,4-ethylenedioxythiophene) , 2005 .

[17]  Jin-seong Park,et al.  CMP characteristics and optical property of ITO thin film by using silica slurry with a variety of process parameters , 2006 .

[18]  Francesca Sarto,et al.  Heterojunction solar cell with 2% efficiency based on a Cu2O substrate , 2006 .

[19]  Yongfang Li.  Molecular design of photovoltaic materials for polymer solar cells: toward suitable electronic energy levels and broad absorption. , 2012, Accounts of chemical research.

[20]  D. Goodman,et al.  Correlation of Relative X-ray Photoelectron Spectroscopy Shake-up Intensity with CuO Particle Size , 1999 .

[21]  Yongfang Li,et al.  High‐Yield Synthesis and Electrochemical and Photovoltaic Properties of Indene‐C70 Bisadduct , 2010 .

[22]  Yongfang Li,et al.  Indene-C(60) bisadduct: a new acceptor for high-performance polymer solar cells. , 2010, Journal of the American Chemical Society.

[23]  Meng Tao,et al.  LSDA+U study of cupric oxide : Electronic structure and native point defects , 2006 .

[24]  Suren A. Gevorgyan,et al.  Degradation patterns in water and oxygen of an inverted polymer solar cell. , 2010, Journal of the American Chemical Society.

[25]  Yang Yang,et al.  A polymer tandem solar cell with 10.6% power conversion efficiency , 2013, Nature Communications.

[26]  Ching-Fuh Lin,et al.  Sol–gel processed CuOx thin film as an anode interlayer for inverted polymer solar cells , 2010 .

[27]  Thomas Riedl,et al.  Low-temperature, solution-processed MoO(x) for efficient and stable organic solar cells. , 2012, ACS applied materials & interfaces.

[28]  Lei Liao,et al.  From Copper Nanocrystalline to CuO Nanoneedle Array: Synthesis, Growth Mechanism, and Properties , 2007 .

[29]  A. C. Jayasuriya,et al.  Fabrication of cuprous and cupric oxide thin films by heat treatment , 2009 .

[30]  Yang Yang,et al.  High-efficiency solution processable polymer photovoltaic cells by self-organization of polymer blends , 2005 .

[31]  D. Ginley,et al.  Enhanced Efficiency in Plastic Solar Cells via Energy Matched Solution Processed NiOx Interlayers , 2011 .

[32]  Kion Norrman,et al.  Water-induced degradation of polymer solar cells studied by H2(18)O labeling. , 2009, ACS applied materials & interfaces.

[33]  Okada,et al.  Triple-peak feature of Cu 2p x-ray-photoemission spectrum in copper acetylacetonate. , 1993, Physical review. B, Condensed matter.

[34]  Zhan'ao Tan,et al.  Synthesis and photovoltaic properties of two-dimensional conjugated polythiophenes with bi(thienylenevinylene) side chains. , 2006, Journal of the American Chemical Society.

[35]  S. Rhee,et al.  Effect of electrode material on the resistance switching of Cu2O film , 2007 .

[36]  T. Riedl,et al.  Solution Processed Vanadium Pentoxide as Charge Extraction Layer for Organic Solar Cells , 2011 .

[37]  Miao Xu,et al.  Enhanced power-conversion efficiency in polymer solar cells using an inverted device structure , 2012, Nature Photonics.

[38]  Barry P Rand,et al.  Solution-processed MoO₃ thin films as a hole-injection layer for organic solar cells. , 2011, ACS applied materials & interfaces.

[39]  Yanming Sun,et al.  Inverted Polymer Solar Cells Integrated with a Low‐Temperature‐Annealed Sol‐Gel‐Derived ZnO Film as an Electron Transport Layer , 2011, Advanced materials.

[40]  Yongfang Li,et al.  Solution-processed vanadium oxide as a hole collection layer on an ITO electrode for high-performance polymer solar cells. , 2012, Physical chemistry chemical physics : PCCP.

[41]  D. Hercules,et al.  Decomposition of Copper Compounds in X-Ray Photoelectron Spectrometers , 1984 .

[42]  C. Brabec,et al.  Impedance Spectroscopy on Polymer-Fullerene Solar Cells , 2007 .

[43]  Nguyen Duc Hoa,et al.  Synthesis of p-type semiconducting cupric oxide thin films and their application to hydrogen detection , 2010 .

[44]  Kevin P. Musselman,et al.  A Novel Buffering Technique for Aqueous Processing of Zinc Oxide Nanostructures and Interfaces, and Corresponding Improvement of Electrodeposited ZnO‐Cu2O Photovoltaics , 2011 .

[45]  Yongfang Li,et al.  Solution-Processed Tungsten Oxide as an Effective Anode Buffer Layer for High-Performance Polymer Solar Cells , 2012 .

[46]  Christoph J. Brabec,et al.  Organic materials: Fantastic plastic , 2008 .

[47]  Yimei Zhu,et al.  Copper oxide nanocrystals. , 2005, Journal of the American Chemical Society.