Light Flapping Micro Aerial Vehicle Using Electrical-Discharge Wire-Cutting Technique

Electrical-discharge wire cutting is a promising technique that provides flexibility and lightness for a flapping micro aerial vehicle. Electrical-discharge wire cutting is used to fabricate the high-aspect-ratio structure of the four-bar linkage gear transmission module made of aluminum-alloy 7075. Aluminum-alloy 7075 has excellent specific strength (yield strength/density) good for durability of the transmission module in a micro aerial vehicle's tuff operation. A new flapping micro aerial vehicle of 21.6 cm wing span consequently has a minimum body mass of 5.9 g after installing the transmission module and a flexible wing frame made of carbon fibers and polyethylene terephthalate film. This micro aerial vehicle can endure a flight time of 6 min 7 s with the wingbeat frequency of 10-20 Hz. The lift and thrust coefficients of the micro aerial vehicle have been investigated through wind-tunnel testing. The proposed flapping micro aerial vehicle also exhibits the improved characteristic in the scaling law with respect to wingbeat frequency versus body mass.

[1]  Y. Tai,et al.  Titanium-alloy MEMS wing technology for a micro aerial vehicle application , 2001 .

[2]  Wen-Bin Young,et al.  The thrust and lift of an ornithopter's membrane wings with simple flapping motion , 2006 .

[3]  Rafal Zbikowski,et al.  Four-Bar Linkage Mechanism for Insectlike Flapping Wings in Hover: Concept and an Outline of Its Realization , 2005 .

[4]  Teerachai Nicholas Pornsinsirirak.  Parylene MEMS technology for adaptive flow control of flapping flight , 2002 .

[5]  M. Dickinson,et al.  Wing rotation and the aerodynamic basis of insect flight. , 1999, Science.

[6]  Roelof Vos,et al.  Post-buckled precompressed (PBP) elements: a new class of flight control actuators enhancing high-speed autonomous VTOL MAVs , 2005, SPIE Smart Structures and Materials + Nondestructive Evaluation and Health Monitoring.

[7]  Sunil K. Agrawal,et al.  Design and Optimization of a Mechanism for Out-of-Plane Insect Winglike Motion With Twist , 2005 .

[8]  Lung-Jieh Yang,et al.  Flapping wings with PVDF sensors to modify the aerodynamic forces of a micro aerial vehicle , 2007 .

[9]  Yu Sun,et al.  MEMS capacitive force sensors for cellular and flight biomechanics , 2007, Biomedical materials.

[10]  Kirill V. Rozhdestvensky,et al.  Aerohydrodynamics of flapping-wing propulsors , 2003 .

[11]  Wei Shyy,et al.  Flapping and flexible wings for biological and micro air vehicles , 1999 .

[12]  R. Zbikowski,et al.  Insect-like flapping wing mechanism based on a double spherical Scotch yoke , 2005, Journal of The Royal Society Interface.

[13]  C. H. Greenewalt.  The Flight of Birds: The Significant Dimensions, Their Departure from the Requirements for Dimensional Similarity, and the Effect on Flight Aerodynamics of That Departure , 1975 .

[14]  C. J. Pennycuick,et al.  Chapter 1 – MECHANICS OF FLIGHT , 1975 .

[15]  A. Hedenström,et al.  Bat Flight Generates Complex Aerodynamic Tracks , 2007, Science.

[16]  Chih-Ming Ho,et al.  Unsteady aerodynamics and flow control for flapping wing flyers , 2003 .

[17]  R. B. Srygley,et al.  Unconventional lift-generating mechanisms in free-flying butterflies , 2002, Nature.

[18]  Lung-Jieh Yang,et al.  A Micro-Aerial-Vehicle (MAV) with figure-of-eight flapping induced by flexible wing frames , 2009 .

[19]  R. Zbikowski.  Fly like a fly [micro-air vehicle] , 2005, IEEE Spectrum.

[20]  Sunil K. Agrawal,et al.  Design of a mechanism for biaxial rotation of a wing for a hovering vehicle , 2006 .

[21]  Max F. Platzer,et al.  Bio-inspired design of flapping-wing micro air vehicles , 2005, The Aeronautical Journal (1968).