Investigating material removal rate and surface roughness using multi-objective optimization for focused ion beam (FIB) micro-milling of cemented carbide

Abstract Cemented carbide has been investigated as a useful material for the fabrication of micro devices. Focused ion beam (FIB) micro-milling has been found to be one of the most appropriate methods for the fabrication of micro devices. The experimental FIB micro-milling on cemented carbide have been conducted according to the L16 orthogonal array of Taguchi technique. Beam current, extraction voltage, angle of beam incidence, dwell time and percentage overlap between beam diameters have been considered as process variables of FIB micro-milling in experimental design. Material removal rate (MRR) and surface roughness have been determined experimentally for FIB micro-milling of cemented carbide and beam current has been identified as the most significant parameter. The minimum surface roughness of 5.6 nm has been reported on cemented carbide, which is not a usual practice to achieve on such polycrystalline material, and hence it may be considered as a significant research contribution. Maximum MRR of 0.4836 μm3/s has been reported. Moreover, genetic algorithm toolbox of MATLAB has been utilized for multi-objective optimization between MRR and surface roughness. The corresponding optimum values of MRR and surface roughness for multi-objective optimization have been represented by pareto optimum solution generated by genetic algorithm. The research work presented in this paper determines the setting of process parameters of FIB micro-milling for achieving a specific combination of MRR and surface roughness on cemented carbide.

[1]  Xiao-Bing Hu,et al.  Multi-objective optimization of material selection for sustainable products: Artificial neural networks and genetic algorithm approach , 2009 .

[2]  Raphael T. Haftka,et al.  Global structural optimization of a stepped cantilever beam using quasi-separable decomposition , 2010 .

[3]  Raja Nassar,et al.  Mathematical modeling of focused ion beam microfabrication , 1998 .

[4]  Baoping Tang,et al.  A novel fault diagnosis model for gearbox based on wavelet support vector machine with immune genetic algorithm , 2013 .

[5]  Stefan Simeonov Dimov,et al.  Patterning of amorphous and polycrystalline Ni78B14Si8 with a focused-ion-beam , 2007 .

[6]  Omid Motlagh,et al.  A genetic algorithm for optimization of integrated scheduling of cranes, vehicles, and storage platforms at automated container terminals , 2014, J. Comput. Appl. Math..

[7]  S. Bhavsar,et al.  Machinability Study of Cemented Carbide Using Focused Ion Beam (FIB) Milling , 2012 .

[8]  Nixon Kuruvila,et al.  PARAMETRIC INFLUENCE AND OPTIMIZATION OF WIRE EDM OF HOT DIE STEEL , 2011 .

[9]  Jun Xu,et al.  Study and formation of 2D microstructures of sapphire by focused ion beam milling , 2008 .

[10]  P. V. Rao,et al.  Experimental investigation of redeposition during focused ion beam milling of high speed steel , 2012 .

[11]  S. Bhavsar,et al.  Machinability study of high speed steel for focused ion beam (FIB) milling process – An experimental investigation at micron/nano scale , 2014 .

[12]  Mamoru Mabuchi,et al.  Fabrication of nanoscale Ti honeycombs by focused ion beam , 2003 .

[13]  M. Marchese,et al.  An ant colony optimization method for generalized TSP problem , 2008 .

[14]  K. F. Russell,et al.  Strategies for fabricating atom probe specimens with a dual beam FIB. , 2005, Ultramicroscopy.

[15]  S. Bhavsar,et al.  An accurate and efficient control over the present numerical model of depth of sputtering in focused ion beam milling , 2009 .

[16]  S. Sharif,et al.  SIMULATED ANNEALING TO ESTIMATE THE OPTIMAL CUTTING CONDITIONS FOR MINIMIZING SURFACE ROUGHNESS IN END MILLING Ti-6Al-4V , 2010 .

[17]  S. Aravindan,et al.  Nanosurface Fabrication of Hard Brittle Materials by Structured Tool Imprinting , 2004 .

[18]  Sead Spuzic,et al.  Optimization of oval-round pass design using genetic algorithm , 2012 .

[19]  Jun Wang,et al.  OPTIMIZATION OF CUTTING CONDITIONS IN DRILLING OPERATIONS WITH PLANE RAKE FACED TWIST DRILLS , 2011 .

[20]  D. D. Winter,et al.  Measurements and calculations of FIB milling yield of bulk metals , 2007 .