In-plane permeability measurements: a nordic round-robin study

Three methods to measure the in-plane permeability are compared. The methods are based on the wetting and saturated parallel flow techniques and the wetting radial flow technique. It is found that the stability of all three methods is very good. The best repeatability in the results is obtained with the wetting parallel flow technique. A main drawback of this method is, however, that the samples are not saturated hence, the saturated parallel flow method is suggested for continued evaluation. The standard deviation from repeatable measurements of this method is 14 and 20% for the two fabrics tested. By a round-robin comparison at three laboratories it is found that the reproducibility of the saturated parallel flow technique is in the same range as the repeatability of the method. Furthermore, it is shown that the liquid tested and the pressure applied have very small influence on the results. It is clear that most of the scatter is due to the sample preparation and variations in the material. Accordingly, a continued work should be concentrated on improvements of the sample preparation, and development of methods to reduce the influence, from small errors, in sample preparation on the results.

[1]  J. Higdon,et al.  Permeability of three-dimensional models of fibrous porous media , 1996, Journal of Fluid Mechanics.

[2]  Sung-Hoon Ahn,et al.  Measurement of the Three-Dimensional Permeability of Fiber Preforms Using Embedded Fiber Optic Sensors , 1995 .

[3]  Alfred C. Loos,et al.  The Effects of Fluid Type and Viscosity on the Steady-State and Advancing Front Permeability Behavior of Textile Preforms , 1997 .

[4]  J. Drummond,et al.  Laminar viscous flow through regular arrays of parallel solid cylinders , 1984 .

[5]  R. Gauvin,et al.  The Modelling of Mold Filling in Resin Transfer Molding , 1986 .

[6]  F. Dullien.  Porous Media: Fluid Transport and Pore Structure , 1979 .

[7]  Ephraim M Sparrow,et al.  Longitudinal Laminar Flow Between Cylinders Arranged in Regular Array , 1959 .

[8]  R. Parnas,et al.  A comparison of the unidirectional and radial in-plane flow of fluids through woven composite reinforcements , 1993 .

[9]  J. Bear.  Dynamics of Fluids in Porous Media , 1975 .

[10]  Vistasp M. Karbhari,et al.  Experimental characterization of permeability and fibre wetting for liquid moulding , 1995 .

[11]  Ludwig Rebenfeld,et al.  Radial penetration of a viscous liquid into a planar anisotropic porous medium , 1988 .

[12]  T. Lundström.  Bubble transport through constricted capillary tubes with application to resin transfer molding , 1996 .

[13]  I. Howells,et al.  Drag on fixed beds of fibres in slow flow , 1998, Journal of Fluid Mechanics.

[14]  T. Lundgren,et al.  Slow flow through stationary random beds and suspensions of spheres , 1972, Journal of Fluid Mechanics.

[15]  Simon L. Goren,et al.  Model for predicting pressure drop and filtration efficiency in fibrous media , 1968 .

[16]  Effect of Perturbation of Fibre Architecture on Permeability Inside Fibre Tows , 1995 .

[17]  Rikard Gebart,et al.  Measurement of in-plane permeability of anisotropic fiber reinforcements , 1996 .

[18]  Rikard Gebart,et al.  Influence from process parameters on void formation in resin transfer molding , 1994 .

[19]  John Happel,et al.  Viscous flow relative to arrays of cylinders , 1959 .

[20]  Adrian E. Scheidegger,et al.  The physics of flow through porous media , 1957 .

[21]  T. Staffan Lundström,et al.  In-plane permeability measurements on fiber reinforcements by the multi-cavity parallel flow technique , 1999 .

[22]  T. Lundström.  Measurement of void collapse during resin transfer moulding , 1997 .

[23]  P. Gudmundson,et al.  An evaluation of alternative injection strategies in RTM , 1992 .

[24]  L. J. Lee,et al.  Experimental investigation of flow-induced microvoids during impregnation of unidirectional stitched fiberglass mat , 1996 .

[25]  W. Young,et al.  Permeability Measurement of Bidirectional Woven Glass Fibers , 1995 .

[26]  E. Kissa,et al.  Wetting and Wicking , 1996 .

[27]  Suresh G. Advani,et al.  Permeability characterization. Part 1: A proposed standard reference fabric for permeability , 1995 .

[28]  H. Brinkman.  A calculation of the viscous force exerted by a flowing fluid on a dense swarm of particles , 1949 .

[29]  B. R. Gebart,et al.  Permeability of Unidirectional Reinforcements for RTM , 1992 .

[30]  Constantina Lekakou,et al.  Measurement techniques and effects on in-plane permeability of woven cloths in resin transfer moulding , 1996 .