Effect of molecular weight on drawing poly(vinyl alcohol) from solution-grown crystal mats

[1]  T. Kanamoto,et al.  Effects of sample geometry and draw conditions on the mechanical properties of drawn poly(ethylene terephthalate) , 1990 .

[2]  J. Chen,et al.  Preparation of high‐strength poly(vinyl alcohol) fibers by crosslinking wet spinning , 1989 .

[3]  D. Grubb,et al.  Effect of drawing on the α relaxation of poly(vinyl alcohol) , 1988 .

[4]  R. Manley,et al.  Drawing-induced changes in the properties of polyethylene fibers prepared by gelation/crystallization , 1988 .

[5]  T. Kunugi,et al.  Preparation of ultra-high modulus polyethylene films by the zone-annealing method , 1988 .

[6]  R. Porter,et al.  Super-drawing of ultrahigh molecular weight polyethylene. 1. Effect of techniques on drawing of single crystal mats , 1988 .

[7]  D. Grubb,et al.  Tensile strength of zone drawn Poly(vinyl alcohol) , 1988 .

[8]  J. Mewis,et al.  Thermoreversible gelation of solutions of poly(vinyl alcohol) , 1988 .

[9]  P. J. Lemstra,et al.  Chain-Extended Polyethylene , 1987 .

[10]  M. Matsuo,et al.  Elastic modulus of polyethylene in the crystal chain direction as measured by X-ray diffraction , 1986 .

[11]  K. Miyasaka,et al.  Drawing of ultrahigh-molecular-weight polyethylene single-crystal mats: the crystallinity , 1986 .

[12]  P. Cebe,et al.  Gel-drawn fibres of poly(vinyl alcohol) , 1985 .

[13]  I. Sakurada.  Polyvinyl Alcohol Fibers , 1985 .

[14]  P. Meakin,et al.  Theoretical study of the influence of the molecular weight on the maximum tensile strength of polymer fibers , 1985 .

[15]  P. Barham,et al.  High-strength polyethylene fibres from solution and gel spinning , 1985 .

[16]  K. Miyasaka,et al.  Drawing of ultrahigh‐molecular‐weight polyethylene single‐crystal mats , 1984 .

[17]  R. Porter,et al.  On the minimum draw ratio necessary for full chain extension: Illustrated with polyethylene , 1983 .

[18]  T. Kanamoto,et al.  On Ultra-High Tensile Modulus by Drawing Single Crystal Mats of High Molecular Weight Polyethylene , 1983 .

[19]  Richard S. Stein,et al.  Small-angle neutron scattering studies on amorphous polystyrene oriented by solid-state coextrusion , 1982 .

[20]  Pj Piet Lemstra,et al.  Ultradrawing of high-molecular-weight polyethylene cast from solution. II.Influence of initial polymer concentration , 1981 .

[21]  S. Deteresa,et al.  Shrinkage as a measure of the deformation efficiency of ultra-oriented high density polyethylene: Authors' addition , 1981 .

[22]  Pj Piet Lemstra,et al.  Ultra-high strength polyethylene filaments by solution spinning/drawing. 3. Influence of drawing temperature , 1980 .

[23]  M. Watts,et al.  Shrinkage as a measure of the deformation efficiency of ultra-oriented high density polyethylene , 1980 .

[24]  Phillip D. Griswold,et al.  Solid State Coextrusion: A New Technique for Ultradrawing Thermoplastics Illustrated with High Density Polyethylene. , 1978 .

[25]  A. Zwijnenburg,et al.  Longitudinal growth of polymer crystals from flowing solutions III. Polyethylene crystals in Couette flow , 1976 .

[26]  P. Barham,et al.  A criterion for distinguishing between polymer fibers of fundamentally different origin , 1975 .