Influence of raw powder preparation routes on properties of hydroxyapatite fabricated by 3D printing technique

A comparison between two routes of raw powder preparation, namely spray drying and grinding, for 3D printing of hydroxyapatite was carried out. Hydroxyapatite particles prepared by the spray drying technique were spherical in shape whereas the grinding route gave irregular-shaped agglomerates. Spray-dried powders had higher tap density than milled powders, however milled powders yielded 3DP specimens with greater green density and strength. After sintering at 1300 °C for 1 and 5 h, samples fabricated from milled powders showed a 32% higher in sintered density, a 20% lower in porosity and approximately two times higher flexural modulus and strength than samples fabricated from spray-dried powders. This difference was related to the better packing characteristics of milled powders which promoted improved inter- and intra-particle densification during high temperature sintering compared to the spray-dried powders which yielded only high intra-particle densification, but lower inter-particle densification.

[1]  A. Rapacz-Kmita,et al.  FTIR and XRD investigations on the thermal stability of hydroxyapatite during hot pressing and pressureless sintering processes , 2005 .

[2]  H. Seitz,et al.  Three-dimensional printing of porous ceramic scaffolds for bone tissue engineering. , 2005, Journal of biomedical materials research. Part B, Applied biomaterials.

[3]  N. Mostafa.  Characterization, thermal stability and sintering of hydroxyapatite powders prepared by different routes , 2005 .

[4]  W. Bonfield,et al.  Calcining influence on the powder properties of hydroxyapatite , 2001, Journal of materials science. Materials in medicine.

[5]  Germany,et al.  A discrete model for long time sintering , 2002, cond-mat/0211280.

[6]  V. Firouzdor,et al.  Sintering of biocompatible P/M Co–Cr–Mo alloy (F-75) for fabrication of porosity-graded composite structures , 2008 .

[7]  H. Aoki,et al.  Mechanical properties of sintered hydroxyapatite for prosthetic applications , 1981 .

[8]  Paul Roschger,et al.  Towards bone replacement materials from calcium phosphates via rapid prototyping and ceramic gelcasting , 2005 .

[9]  A. Simchi,et al.  3D Printing of Biocompatible PM-Materials , 2007 .

[10]  S. Milz,et al.  Hydroxyapatite scaffolds for bone tissue engineering made by 3D printing , 2005, Journal of materials science. Materials in medicine.

[11]  E. D. Rekow,et al.  Performance of hydroxyapatite bone repair scaffolds created via three-dimensional fabrication techniques. , 2003, Journal of biomedical materials research. Part A.

[12]  O. Harrysson,et al.  Direct metal fabrication of titanium implants with tailored materials and mechanical properties using electron beam melting technology , 2008 .

[13]  Y. Akimune,et al.  Effect of Grain Growth of β‐Silicon Nitride on Strength, Weibull Modulus, and Fracture Toughness , 1993 .

[14]  M. Trunec,et al.  Kinetics of thermal decomposition of hydroxyapatite bioceramics , 1999 .

[15]  A. Simchi,et al.  An investigation on the compressibility of aluminum/nano-alumina composite powder prepared by blending and mechanical milling , 2007 .

[16]  Hao Wang,et al.  Influence of hot pressing sintering temperature and time on microstructure and mechanical properties of TiB2 ceramics , 2002 .

[17]  T. Hirai,et al.  Tough multilayered α–β SI3N4 ceramics prepared by spark plasma sintering , 2001 .

[18]  F. Lin,et al.  Thermal decomposition and reconstitution of hydroxyapatite in air atmosphere. , 1999, Biomaterials.

[19]  Amit Bandyopadhyay,et al.  Development of controlled porosity polymer-ceramic composite scaffolds via fused deposition modeling , 2003 .

[20]  K. Leong,et al.  Solid freeform fabrication of three-dimensional scaffolds for engineering replacement tissues and organs. , 2003, Biomaterials.

[21]  E. D. Rekow,et al.  Engineered cellular response to scaffold architecture in a rabbit trephine defect. , 2003, Journal of biomedical materials research. Part A.

[22]  K. Lu,et al.  3DP process for fine mesh structure printing , 2008 .

[23]  Kriskrai Sitthiseripratip,et al.  3D printing of hydroxyapatite: Effect of binder concentration in pre-coated particle on part strength , 2007 .

[24]  T. Mangialardi.  Sintering of MSW fly ash for reuse as a concrete aggregate. , 2001, Journal of hazardous materials.

[25]  E. D. Rekow,et al.  MicroCT analysis of hydroxyapatite bone repair scaffolds created via three-dimensional printing for evaluating the effects of scaffold architecture on bone ingrowth. , 2008, Journal of biomedical materials research. Part A.