The lubrication of metal-on-metal total hip joints: A slide down the Stribeck curve

Abstract Metal-on-metal joints can exhibit profoundly different modes of lubrication when tested in a hip simulator. A range of metal-on-metal joints of similar diameters differing only in diametral clearance can demonstrate differences in lubrication conditions during simulator testing, as can joints differing principally in diameter. Simulated walking cycles can similarly cause differences in lubricating conditions through the application of different motion and loading cycles. In this study, and work conducted previously by the authors, metal-on-metal joints were tested in 25 per cent bovine serum in a hip simulator. A simple resistivity technique was used to detect surface contact, or separation, in a lubrication study, while a wear study used a gravimetric protocol extending over at least 2000000 cycles duration. Simulated physiological and simplified walking cycles were used during the studies to investigate the effect of motion and load on lubrication and wear. Joints of 16, 22.225, 28 and 36 mm nominal diameter were tested to investigate the effect of diameter, while the effect of diametral clearance was studied using joints of 36 mm diameter with a range of diametral clearances from 97 to 170μm. The trend of an idealized Stribeck curve, plotted as coefficient of friction versus the dimensionless Sommerfeld parameter (viscosity × sliding velocity × radius of the femoral head/load), indicates the lubrication regime prevalent in a joint. Boundary, mixed and fluid-film lubrication, shown by the three classic regions on an idealized Stribeck curve, were all demonstrated using metal-on-metal joints in a hip simulator. The different modes of lubrication prevalent in the joints resulted in wear rates spanning two orders of magnitude between joints differing principally in diameter. Similarly, a reduction in diametral clearance caused a general increase in the proportion of surface separation per simulated walking cycle. Likewise, a simplified walking cycle generated more surface separation per walking cycle for the same joint subjected to a simulated physiological cycle. However, the two walking cycles generated no significant difference in simulator wear rates.

[1]  J Fisher,et al.  A hip joint simulator study using simplified loading and motion cycles generating physiological wear paths and rates , 1999, Proceedings of the Institution of Mechanical Engineers. Part H, Journal of engineering in medicine.

[2]  J Fisher,et al.  Polyethylene particles of a 'critical size' are necessary for the induction of cytokines by macrophages in vitro. , 1998, Biomaterials.

[3]  B. Morrey,et al.  Effect of femoral head size on wear of the polyethylene acetabular component. , 1990, The Journal of bone and joint surgery. American volume.

[4]  A. Taylor,et al.  Systemic distribution of wear debris after hip replacement. A cause for concern? , 1992, Journal of Bone and Joint Surgery-british Volume.

[5]  Michael Tanzer,et al.  Engineering issues and wear performance of metal on metal hip implants. , 1996, Clinical orthopaedics and related research.

[6]  J N Wilson,et al.  Epiphyseal transplantation. A clinical study. , 1966, The Journal of bone and joint surgery. American volume.

[7]  Y Ikada,et al.  Effect of the size and surface charge of polymer microspheres on their phagocytosis by macrophage. , 1988, Biomaterials.

[8]  D Dowson,et al.  Development of a ten-station, multi-axis hip joint simulator , 1999, Proceedings of the Institution of Mechanical Engineers. Part H, Journal of engineering in medicine.

[9]  M. Talbert,et al.  Changes seen in lymph nodes draining the sites of large joint prostheses. , 1989, The American journal of surgical pathology.

[10]  K. Ono,et al.  Revision of residual deformities after operations for duplication of the thumb. , 1990, The Journal of bone and joint surgery. American volume.

[11]  M. Ritter,et al.  Radiolucency at the bone-cement interface in total knee replacement. The effects of bone-surface preparation and cement technique. , 1994, The Journal of bone and joint surgery. American volume.

[12]  M. Semlitsch,et al.  Clinical wear behaviour of ultra-high molecular weight polyethylene cups paired with metal and ceramic ball heads in comparison to metal-on-metal pairings of hip joint replacements , 1997, Proceedings of the Institution of Mechanical Engineers. Part H, Journal of engineering in medicine.

[13]  J O Galante,et al.  Composition and morphology of wear debris in failed uncemented total hip replacement. , 1994, The Journal of bone and joint surgery. British volume.

[14]  I. Clarke,et al.  Metal-on-metal bearing in hip prosthesis generates 100-fold less wear debris than metal-on-polyethylene. , 1999, Acta orthopaedica Scandinavica.

[15]  J Fisher,et al.  Quantitative analysis of wear and wear debris from metal-on-metal hip prostheses tested in a physiological hip joint simulator. , 2001, Bio-medical materials and engineering.

[16]  J. P. Paul,et al.  Paper 8: Forces Transmitted by Joints in the Human Body: , 1966 .

[17]  D. Dowson,et al.  Direct experimental evidence of lubrication in a metal-on-metal total hip replacement tested in a joint simulator , 2000 .

[18]  D. Dowson,et al.  The effect of femoral head diameter upon lubrication and wear of metal-on-metal total hip replacements , 2001, Proceedings of the Institution of Mechanical Engineers. Part H, Journal of engineering in medicine.

[19]  J. Galante,et al.  Macrophage/particle interactions: effect of size, composition and surface area. , 1994, Journal of biomedical materials research.

[20]  S. Smith,et al.  Simplified motion and loading compared to physiological motion and loading in a hip joint simulator , 2000, Proceedings of the Institution of Mechanical Engineers. Part H, Journal of engineering in medicine.

[21]  M. Müller.  The benefits of metal-on-metal total hip replacements. , 1995, Clinical Orthopaedics and Related Research.

[22]  J. K. Lancaster,et al.  Dry bearings: a survey of materials and factors affecting their performance , 1973 .

[23]  G K McKee,et al.  Replacement of arthritic hips by the McKee-Farrar prosthesis. , 1966, The Journal of bone and joint surgery. British volume.

[24]  T. Oegema,et al.  Residual chymopapain activity after chemonucleolysis in normal intervertebral discs in dogs. , 1992, The Journal of bone and joint surgery. American volume.

[25]  A. Yau,et al.  The effect of age on the change in deformity after radical resection and anterior arthrodesis for tuberculosis of the spine. , 1994, The Journal of bone and joint surgery. American volume.

[26]  D Dowson,et al.  A comparative joint simulator study of the wear of metal-on-metal and alternative material combinations in hip replacements , 2000, Proceedings of the Institution of Mechanical Engineers. Part H, Journal of engineering in medicine.

[27]  D. Dowson,et al.  The effect of diametral clearance, motion and loading cycles upon lubrication of metal-on-metal total hip replacements , 2001 .

[28]  D. Murray,et al.  Macrophages stimulate bone resorption when they phagocytose particles. , 1990, The Journal of bone and joint surgery. British volume.

[29]  D Dowson,et al.  A full numerical analysis of hydrodynamic lubrication in artificial hip joint replacements constructed from hard materials , 1999 .

[30]  Duncan Dowson,et al.  Laboratory wear tests and clinical observations of the penetration of femoral heads into acetabular cups in total replacement hip joints: II: A microscopical study of the surfaces of Charnley polyethylene acetabular sockets , 1985 .

[31]  P. Campbell,et al.  Metal on metal total hip replacement workshop consensus document. , 1996, Clinical orthopaedics and related research.

[32]  C. Case,et al.  Widespread dissemination of metal debris from implants. , 1994, The Journal of bone and joint surgery. British volume.

[33]  A Unsworth,et al.  Wear in Retrieved Charnley Acetabular Sockets , 1996, Proceedings of the Institution of Mechanical Engineers. Part H, Journal of engineering in medicine.

[34]  H. W. Ruediger,et al.  Increased blood cobalt and chromium after total hip replacement. , 1999, Journal of toxicology. Clinical toxicology.