CFD simulation of sand particle erosion in gas-dominant multiphase flow

Abstract A method for exploration of erosion in multiphase flow can be Computational Fluid Dynamics (CFD). A key advantage of utilizing CFD is that it can deliver a great deal of information such as the effects of different parameters on erosion, maximum erosion rate, and areas susceptible to erosion damage. The current work used a computational fluid dynamics (CFD) approach to study sand particle erosion in elbows, while the carrier fluid was multiphase flow of low, medium, and high gas flow rates. First, ANSYS MultiFluid VOF model was employed to simulate air–water multiphase flow with superficial gas velocities of 10.1, 18.3, and 27.1 m/s, while superficial liquid velocity was 0.3 m/s in all cases examined. The CFD data were validated against some experimental data previously obtained by a wire-mesh sensor. In the next step, particle tracking and erosion modeling were performed. Specifically, erosion in air–water flow with sand particles of two different sizes (150 and 300 μm) in a 76.2 mm elbow was simulated and compared with experimental data formerly obtained by an ultrasonic technique. Six different erosion equations were employed to discover which equation provides the best predictions. A good agreement was found between CFD results and the experimental data.

[1]  Stojan Petelin,et al.  Coupling of the interface tracking and the two-fluid models for the simulation of incompressible two-phase flow , 2001 .

[2]  Kun Luo,et al.  Large Eddy Simulation of the Anti-Erosion Characteristics of the Ribbed-Bend in Gas-Solid Flows , 2004 .

[3]  Siamack A. Shirazi,et al.  Numerical and experimental investigation of the relative erosion severity between plugged tees and elbows in dilute gas/solid two-phase flow , 2006 .

[4]  Uwe Hampel,et al.  Experimental investigation of interfacial structures within churn flow using a dual wire-mesh sensor , 2015 .

[5]  Siamack A. Shirazi,et al.  A comprehensive review of solid particle erosion modeling for oil and gas wells and pipelines applications , 2014 .

[6]  Mazdak Parsi.  Sand Particle Erosion In Vertical Slug/Churn Flow , 2015 .

[7]  Siamack A. Shirazi,et al.  Modeling Solid Particle Erosion in Elbows and Plugged Tees , 2001 .

[8]  Ronald E. Vieira.  Sand erosion model improvement for elbows in gas production, multiphase annular and low-liquid flow , 2014 .

[9]  Y. Oka,et al.  Practical estimation of erosion damage caused by solid particle impact: Part 1: Effects of impact parameters on a predictive equation , 2005 .

[10]  Siamack A. Shirazi,et al.  A CFD Based Correlation for Erosion Factor for Long-Radius Elbows and Bends , 2001 .

[11]  J. H. Neilson,et al.  Erosion by a stream of solid particles , 1968 .

[12]  Edmund F. Rybicki,et al.  Effect of Particle Size and Liquid Viscosity on Erosion in Annular and Slug Flow , 2014 .

[13]  Edmund F. Rybicki,et al.  Comparison of computed and measured particle velocities and erosion in water and air flows , 2007 .

[14]  Siamack A. Shirazi,et al.  Improved CFD modeling and validation of erosion damage due to fine sand particles , 2015 .

[15]  J. Boulanger,et al.  Modelling the Effect of Particle Size Distribution in Multiphase Flows with Computational Fluid Dynamics and Physical Erosion Experiments , 2014 .

[16]  Siamack A. Shirazi,et al.  Ultrasonic Measurement of Multiphase Flow Erosion Patterns in a Standard Elbow , 2013 .

[17]  Ronald E. Vieira,et al.  Ultrasonic measurements of sand particle erosion in gas dominant multiphase churn flow in vertical pipes , 2015 .

[18]  Michael Fairweather,et al.  Modelling of pipe bend erosion by dilute particle suspensions , 2012, Comput. Chem. Eng..

[19]  Siamack A. Shirazi,et al.  Development of mechanistic erosion equation for solid particles , 2015 .

[20]  W. Tabakoff,et al.  Erosion Prediction in Turbomachinery Resulting from Environmental Solid Particles , 1975 .