A novel analytical model based on arc tangent velocity field for prediction of rolling force in strip rolling

Accurate prediction of rolling force is an effective method to improve strip quality in rolling process. To achieve this goal, a novel arc tangent velocity field model based on the upper bound method is proposed to evaluate the rolling force. The mathematical expression of rolling force is derived from the virtual work principle and maximum plastic work principle. Comparing the experimental results with the proposed analytical model prediction, it has been found that this model is good for estimation of rolling force. Meanwhile, the finite element method is also used to simulate the rolling process to verify the validity of the analytical model. It is shown that this model can be used for prediction of rolling force in practice.

[1]  H. Altenbach,et al.  Numerical Modeling Rolling Contact Problem and Elasticity Deformation of Rolling Die under Hot Milling , 2018, Metals.

[2]  Jinhua Ruan,et al.  An improved inverse method by envelope fitting for prediction of contact stresses in strip rolling , 2017 .

[3]  H. Altenbach,et al.  Modeling fatigue crack and spalling for rolling die under hot milling , 2019, Fatigue & Fracture of Engineering Materials & Structures.

[4]  Changming Liu,et al.  A simplified method to calculate the rolling force in hot rolling , 2017 .

[5]  J. Sun,et al.  Three-dimensional analysis of edge rolling based on dual-stream function velocity field theory , 2018, Journal of Manufacturing Processes.

[6]  Y. Alinia,et al.  Stress analysis in rolling contact problem of a finite thickness FGM layer , 2018, Meccanica (Milano. Print).

[7]  Q. Le,et al.  Analysis of temperature distribution in the hot plate rolling of Mg alloy by experiment and finite element method , 2015 .

[8]  Fangjun Luan,et al.  The calculation of vertical rolling force by using angular bisector yield criterion and Pavlov principle , 2016 .

[9]  A. Nosrati,et al.  Upper bound analysis of wire flat rolling with experimental and FEM verifications , 2019, Meccanica.

[10]  Liang Yun Lan,et al.  Derivation of Equal Area Criterion and its Application to Crack Tip Plastic Zone Analysis , 2011 .

[11]  Shun-hu Zhang,et al.  A dynamic closure criterion for central defects in heavy plate during hot rolling , 2016 .

[12]  S. Li,et al.  A novel analytical model for prediction of rolling force in hot strip rolling based on tangent velocity field and MY criterion , 2019, Journal of Manufacturing Processes.

[13]  Changming Liu,et al.  Research on the influence of nonlocal effect on specific roll pressure by nonlocal stress gradient model in strip rolling , 2018 .

[14]  H. Altenbach,et al.  Modeling creep-fatigue interaction damage and H13 tool steel material response for rolling die under hot milling , 2020 .

[16]  J. G. Lenard,et al.  Friction and Forward Slip in Cold Strip Rolling , 1992 .

[17]  Liu Changming,et al.  Hydrodynamics Method and Its Application in Hot Strip Rolling , 2017 .

[18]  Jong-jin Park.  Finite-element analysis of severe plastic deformation in differential-speed rolling , 2015 .

[21]  Saeed Ziaei-Rad,et al.  Finite Element Analysis on Chattering in Cold Rolling and Comparison With Experimental Results , 2015 .

[22]  L. Changming,et al.  Research of the indirect friction sensor for prediction of contact stress by improved inverse method in strip rolling , 2017 .

[23]  Z. Ren,et al.  Establishment of the tension stress model considering metal lateral flow for foil rolling , 2019, Meccanica.

[24]  L. W. Zhang,et al.  Finite element simulation based plate edging model for plan view pattern control during wide and heavy plate rolling , 2015 .

[25]  Guodong Wang,et al.  Derivation of plastic specific work rate for equal area yield criterion and its application to rolling , 2010 .

[26]  Kornel Ehmann,et al.  A dynamic model of the rolling process. Part I: homogeneous model , 2000 .

[27]  Chen Jie,et al.  Research on rolling force model in hot-rolling process of aluminum alloys , 2011 .