Improvement of a Film-Cooled Blade by Application of the Conjugate Calculation Technique

The conjugate calculation technique has been used for the three-dimensional thermal load prediction of a film-cooled test blade of a modern gas turbine. Thus, it becomes possible to take into account the interaction of internal flows, external flow, and heat transfer without the prescription of heat transfer coefficients. The numerical models consist of all internal flow passages and cooling hole rows, including shaped holes. Based on the results, deficiencies of the test configuration close to the leading edge region and in the blade tip region have been detected, which lead to hot spots and surface areas of high thermal load. These regions of high thermal load have been confirmed by thermal index paint measurements in good agreement to the conjugate calculation results. Based on the experimental and numerical results, recommendations for the improvement of the blade cooling were derived and an improved blade-cooling configuration has been designed. The conjugate calculation results, as well as new measurement data, show that the changes in the cooling design have been successful with respect to cooling performance. Regions of high thermal load have vanished, and effective cooling is reached for all critical parts of the test blade.

[1]  James D. Heidmann,et al.  Conjugate Heat Transfer Effects on a Realistic Film-Cooled Turbine Vane , 2003 .

[2]  Karsten Kusterer,et al.  Conjugate Calculations for a Film-Cooled Blade Under Different Operating Conditions , 2004 .

[3]  James H. Leylek,et al.  Three-Dimensional Conjugate Heat Transfer Simulation of an Internally-Cooled Gas Turbine Vane , 2003 .

[4]  Takao Sugimoto,et al.  Development of a 20MW-Class High-Efficiency Gas Turbine L20A , 2002 .

[5]  Karsten Kusterer,et al.  3-D Conjugate Flow and Heat Transfer Calculations of a Film-Cooled Turbine Guide Vane at Different Operation Conditions , 1997 .

[6]  Dieter Bohn,et al.  Conjugate Analysis Of A Test Configuration For A Film-cooled Blade Under Off-design Conditions , 2003 .

[7]  Meng-Sing Liou,et al.  On the Application of Chimera/Unstructured Hybrid Grids for Conjugate Heat Transfer , 1996 .

[8]  Bruno Facchini,et al.  Conjugate Heat Transfer Simulation of a Radially Cooled Gas Turbine Vane , 2004 .

[9]  David L. Rigby,et al.  Conjugate Heat Transfer Analysis of Internally Cooled Configurations , 2001 .

[10]  Dieter Bohn,et al.  Conjugate Heat Transfer Analysis of a Test Configuration for a Film-cooled Blade , 2003 .

[11]  Kazunori Watanabe,et al.  Thermal Conjugate Analysis of a First Stage Blade in a Gas Turbine , 2000 .

[12]  Takao Sugimoto,et al.  A Review of L20A Engine Design and Field Operating Experience , 2004 .

[13]  George S. Dulikravich,et al.  Simultaneous Prediction of External Flow-Field and Temperature in Internally Cooled 3-D Turbine Blade Material , 2000 .

[14]  Alain J. Kassab,et al.  A coupled FVM/BEM approach to conjugate heat transfer in turbine blades , 1994 .

[15]  Alain J. Kassab,et al.  Numerical prediction of fluid flow and heat transfer in turbine blades with internal cooling , 1994 .

[16]  H. Lomax,et al.  Thin-layer approximation and algebraic model for separated turbulent flows , 1978 .

[17]  Yoji Okita,et al.  Conjugate Heat Transfer Analysis of Turbine Rotor-Stator System , 2002 .

[18]  Moeljo Soetrisno,et al.  Coupled flow and heat transfer analysis using hybrid structured-unstructured grids , 1996 .