Actuation behaviour of layered composites of polyaniline, carbon nanotubes and polypyrrole

Abstract Layered composites of polyaniline (PAn), single-walled carbon nanotubes (CNTs) and polypyrrole (PPy) were produced by coating PAn or PAn/CNT on a PPy hollow fibre containing a platinum (Pt) helix. The actuation behaviour of PAn/PPy and PAn/CNT/PPy composites was compared with that of neat PPy. The Pt helix reduces the IR drop along the fibre, thus enhancing the actuation strain. Components of the composite with low actuation strain such as PAn and/or CNT restrict the actuation displacement of the PPy substrate causing a reduced strain in the composite. In particular, a minimal quantity of CNT (1.3 wt.%) in the composite leads to a discernible decrease in actuation strain but also increases the Young's modulus and tensile strength of the composite. Sodium nitrate (1 M) aqueous solution used as an electrolyte gives good actuation stability where the actuation strain is almost independent of applied stress (5–12 MPa). This can be explained by the unchanged Young's modulus at the reduced (contracted) and oxidized (expanded) states during the actuation process. The polyaniline/polypyrrole composite produced the highest work-per-cycle reported to date under isotonic conditions.

[1]  A. MacDiarmid,et al.  Electrochemical Characteristics of “Polyaniline” Cathodes and Anodes in Aqueous Electrolytes , 1985 .

[2]  Geoffrey M. Spinks,et al.  Carbon nanotube and polyaniline composite actuators , 2003 .

[3]  Geoffrey M. Spinks,et al.  Mechanism of electromechanical actuation in polypyrrole , 1995 .

[4]  M. Nardelli,et al.  MECHANISM OF STRAIN RELEASE IN CARBON NANOTUBES , 1998 .

[5]  J. Schlenoff,et al.  Doping-induced strain in polyaniline : stretchoelectrochemistry , 1993 .

[6]  G. Wallace,et al.  Strain Response from Polypyrrole Actuators under Load , 2002 .

[7]  R. Baughman.  Conducting polymer artificial muscles , 1996 .

[8]  D. Schuster,et al.  High dissolution and strong light emission of carbon nanotubes in aromatic amine solvents. , 2001, Journal of the American Chemical Society.

[9]  Binbin Xi,et al.  Enhanced control and stability of polypyrrole electromechanical actuators , 2004 .

[10]  G. Wallace,et al.  Use of Ionic Liquids for π-Conjugated Polymer Electrochemical Devices , 2002, Science.

[11]  Jie Ding,et al.  High performance conducting polymer actuators utilising a tubular geometry and helical wire interconnects , 2003 .

[12]  O. Chauvet,et al.  Synthesis of a new polyaniline/nanotube composite: “in-situ” polymerisation and charge transfer through site-selective interaction , 2001 .

[13]  Dezhi Zhou,et al.  The amounts per cycle of polypyrrole electromechanical actuators , 2003 .

[14]  Victor Giurgiutiu,et al.  Energy-Based Comparison of Solid-State Induced-Strain Actuators , 1996 .

[15]  Mei Gao,et al.  Scanning tunneling microscopy of aligned coaxial nanowires of polyaniline passivated carbon nanotubes , 2001 .

[16]  A. Rinzler,et al.  Carbon nanotube actuators , 1999, Science.

[17]  Peter Sommer-Larsen,et al.  A Conducting Polymer Artificial Muscle with 12 % Linear Strain , 2003 .

[18]  D. De Rossi,et al.  Performance and work capacity of a polypyrrole conducting polymer linear actuator , 1997 .

[19]  G. Wallace,et al.  In-situ mechanical properties of tosylate doped (pts) polypyrrole , 1997 .

[20]  Jianguo Deng,et al.  Carbon nanotube–polyaniline hybrid materials , 2002 .

[21]  G. A. D. Briggs,et al.  Elastic and shear moduli of single-walled carbon nanotube ropes , 1999 .

[22]  K. West,et al.  Mechanism of Actuation in Conducting Polymers: Osmotic Expansion , 2001 .