Piezoresistive sensing of bistable micro mechanism state

The objective of this work is to demonstrate the feasibility of on-chip sensing of bistable mechanism state using the piezoresistive properties of polysilicon, thus eliminating the need for electrical contacts. Changes in position are detected by observing changes in resistance across the mechanism. Sensing the state of bistable mechanisms is critical for various applications, including high-acceleration sensing arrays and alternative forms of nonvolatile memory. A fully compliant bistable micro mechanism was designed, fabricated and tested to demonstrate the feasibility of this sensing technique. Testing results from two fabrication processes, SUMMiT IV and MUMPs, are presented. The SUMMiT mechanism was then integrated into various Wheatstone bridge configurations to investigate their potential advantages and to demonstrate various design layouts. Repeatable and detectable results were found with independent mechanisms and with those integrated into Wheatstone bridges.

[1]  Nadim Maluf,et al.  An Introduction to Microelectromechanical Systems Engineering , 2000 .

[2]  Hans Joachim Quenzer,et al.  Bistable microvalve with pneumatically coupled membranes , 1996, Proceedings of Ninth International Workshop on Micro Electromechanical Systems.

[3]  J. W. Wittwer,et al.  Robust design and model validation of nonlinear compliant micromechanisms , 2005, Journal of Microelectromechanical Systems.

[4]  V. A. Gridchin,et al.  Phenomenological Model of the Piezoresistive Effect in Polysilicon Films , 2003 .

[5]  Larry L. Howell,et al.  Predicting the Performance of a Bistable Micro Mechanism Using Design-Stage Uncertainty Analysis , 2002 .

[6]  J. F. Verwey,et al.  Nonvolatile Semiconductor Memories , 1976 .

[7]  H. E. Elgamel,et al.  Closed-form expressions for the relationships between stress, diaphragm deflection, and resistance change with pressure in silicon piezoresistive pressure sensors , 1995 .

[8]  Larry L. Howell,et al.  AN INVESTIGATION INTO COMPLIANT BISTABLE MECHANISMS , 1998 .

[9]  J. Brewer,et al.  Nonvolatile semiconductor memory technology : a comprehensive guide to understanding and to using NVSM devices , 1998 .

[10]  Robert K. Messenger.  Modeling and Control of Surface Micromachined Thermal Actuators , 2004 .

[11]  Matthew B. Parkinson,et al.  Optimization-Based Design of a Fully-Compliant Bistable Micromechanism , .

[12]  Timothy W. McLain,et al.  FEEDBACK CONTROL OF A THERMOMECHANICAL INPLANE MICROACTUATOR USING PIEZORESISTIVE DISPLACEMENT SENSING , 2004 .

[13]  James H. Smith,et al.  Planar Surface-Micromachined Pressure Sensor with a Sub-Surface , Embedded Reference Pressure Cavity , 1997 .

[14]  J. Lang,et al.  A high-current electrothermal bistable MEMS relay , 2003, The Sixteenth Annual International Conference on Micro Electro Mechanical Systems, 2003. MEMS-03 Kyoto. IEEE.

[15]  Ray Bert,et al.  Book Review: Introduction to Transportation Systems by Joseph Sussman. Boston: Artech House, 2000 , 2002 .

[16]  R. Schellin,et al.  A silicon subminiature microphone based on piezoresistive polysilicon strain gauges , 1992 .

[17]  M. Madou.  Fundamentals of microfabrication , 1997 .

[18]  M. Gad-el-Hak.  The MEMS Handbook , 2001 .

[19]  Patrick J. French,et al.  Polycrystalline silicon as a strain gauge material , 1986 .

[20]  Brian D. Jensen,et al.  Identification of Macro- and Micro-Compliant Mechanism Configurations Resulting in Bistable Behavior , 2003 .

[21]  Charles S. Smith.  Piezoresistance Effect in Germanium and Silicon , 1954 .

[22]  Larry L. Howell,et al.  Design of two-link, in-plane, bistable compliant micro-mechanisms , 1999 .

[23]  Larry L. Howell,et al.  Thermal Modeling of a Surface-micromachined Linear Thermomechanical Actuator , 2001 .

[24]  B. Halg.  On a micro-electro-mechanical nonvolatile memory cell , 1990 .

[25]  Chenming Hu.  Nonvolatile semiconductor memories : technologies, design, and applications , 1991 .

[26]  D. Belavic,et al.  Numerical simulation and experimental verification of the piezoresistivity phenomenon for the printed thick-film piezoresistors , 2004, 5th International Conference on Thermal and Mechanical Simulation and Experiments in Microelectronics and Microsystems, 2004. EuroSimE 2004. Proceedings of the.

[27]  Srinivas Tadigadapa,et al.  Developments in Microelectromechanical Systems (MEMS): A Manufacturing Perspective , 2003 .

[28]  Ian G. Foulds,et al.  A surface micromachined bistable switch , 2002, IEEE CCECE2002. Canadian Conference on Electrical and Computer Engineering. Conference Proceedings (Cat. No.02CH37373).

[29]  J. Qiu,et al.  A centrally-clamped parallel-beam bistable MEMS mechanism , 2001, Technical Digest. MEMS 2001. 14th IEEE International Conference on Micro Electro Mechanical Systems (Cat. No.01CH37090).

[30]  Patrick J. French,et al.  Polycrystalline Silicon Strain Sensors , 1985 .

[31]  P. French,et al.  Piezoresistance in polysilicon and its applications to strain gauges , 1989 .