Freeze start drive cycle simulation of a fuel cell powertrain with a two-phase stack model and exergy analysis for thermal management improvement

Abstract This paper integrates a two-phase fuel cell stack model, previously published and validated in Tang et al. (2017) for the specific purpose of investigating freeze start behavior, into a full-hybrid fuel cell powertrain model to simulate cold start. The aim of the simulation is to provide an overview of exergy loss distribution during a cold start drive cycle scenario. Another intention is to propose a methodology for suggesting the directions in thermal management development. The powertrain model simulates an Artemis-like transient drive cycle starting from −20 °C. The heater-core bypass and fuel cell stack power threshold are selected as representative thermal/energy management options. To evaluate the impact of the selected options on the warm up, the accumulated energy consumption and exergy flow rates are analyzed. The statistics from our simulation show that the inefficient energy consumption occurs mainly in the city stage shortly after the successful freeze start. The tank-to-wheel efficiency merely achieves 10.3% in the city stage, while the fuel cell stack can reach nearly 73% exergy efficiency throughout the entire drive cycle and tank-to-wheel efficiency reaches 29.3% at the end of the whole drive cycle. The improvement is suggested to be focused in the low power demand stages by cutting down to the actual power ratio needed and simultaneously minimize the relevant thermal-hydraulic inertia. Several optimization directions such as cascaded fuel cell stack alignment, split cooling and power demand threshold for active rapid warm up are drawn. The established fuel cell powertrain model combined with exergy analysis is a suitable methodology for further detailed thermal and energy management investigations.

[1]  Sousso Kelouwani,et al.  Proton exchange membrane fuel cells cold startup global strategy for fuel cell plug-in hybrid electric vehicle , 2012 .

[2]  Wilhelm Tegethoff,et al.  A spatially resolved fuel cell stack model with gas–liquid slip phenomena for cold start simulations , 2017 .

[3]  Azizul Mohamad,et al.  A Review of Experiments on Cold Start of PEM Fuel Cells , 2013 .

[4]  Ferit Küçükay,et al.  Innovative electric vehicle modelling for energy management applications , 2015 .

[5]  Takemi Chikahisa,et al.  Ice Formation Processes in PEM Fuel Cell Catalyst Layers during Cold Startup Analyzed by Cryo-SEM , 2016 .

[6]  Tian Tang,et al.  Analyse der Energieeffizienz eines Brennstoffzellenstapels im Kaltstartbetrieb , 2016 .

[7]  Jun Liu,et al.  Effect of entropy change of lithium intercalation in cathodes and anodes on Li-ion battery thermal management , 2010 .

[8]  Oliver Berger.  Thermodynamische Analyse eines Brennstoffzellensystems zum Antrieb von Kraftfahrzeugen , 2009 .

[9]  Fernando Beltrán Cilleruelo,et al.  A new approach to battery powered electric vehicles: A hydrogen fuel-cell-based range extender system , 2016 .

[10]  C. Schultze,et al.  Contribution to Numerically Efficient Modelling of Thermodynamic SystemsA , 2013 .

[11]  Hee Chun Lim,et al.  Pressure and flow distribution in internal gas manifolds of a fuel-cell stack , 2003 .

[12]  Wilhelm Tegethoff,et al.  Modelling of heat pumps with an object-oriented model library for thermodynamic systems , 2010 .

[13]  Mingyu Huang,et al.  Research on hybrid ratio of fuel cell hybrid vehicle based on ADVISOR , 2016 .

[14]  Dieter Brüggemann,et al.  Experimental investigation of parameters influencing the freeze start ability of a fuel cell system , 2009 .

[15]  Xianguo Li,et al.  On the modeling of water transport in polymer electrolyte membrane fuel cells , 2009 .

[16]  Yoshiaki Naganuma,et al.  Development of System Control for Rapid Warm-up Operation of Fuel Cell , 2012 .

[17]  Fabien Harel,et al.  Experimental Studies on the Influence of Operational Parameters on the Cold Start of a 2 kW Fuel Cell , 2008 .

[18]  B. Wetton,et al.  Flow distribution in proton exchange membrane fuel cell stacks , 2006 .

[19]  Ryan James Balliet,et al.  Modeling Cold Start in a Polymer-Electrolyte Fuel Cell , 2010 .

[20]  Manish Khandelwal,et al.  One-dimensional thermal model of cold-start in a polymer electrolyte fuel cell stack , 2007 .

[21]  Loic Boulon,et al.  Multi-stack Fuel Cells Powering a Vehicle , 2015 .

[22]  Liangfei Xu,et al.  Multi-objective energy management optimization and parameter sizing for proton exchange membrane hybrid fuel cell vehicles , 2016 .

[23]  Ibrahim Dincer,et al.  Thermodynamic analysis of a PEM fuel cell power system , 2005 .

[24]  Zhongmin Wan,et al.  A Review on Cold Start of Proton Exchange Membrane Fuel Cells , 2014 .

[25]  Takemi Chikahisa,et al.  Analysis of ice formation process in cathode catalyst layer of PEFC at cold start , 2012 .

[26]  Hua Meng,et al.  Numerical studies of cold‐start phenomena in PEM fuel cells: A review , 2011 .

[27]  Christoph Richter,et al.  Proposal of New Object-Oriented Equation-Based Model Libraries for Thermodynamic Systems , 2008 .

[28]  Kyoungdoug Min,et al.  Dynamic modeling of a proton exchange membrane fuel cell system with a shell-and-tube gas-to-gas membrane humidifier , 2012 .

[29]  Christian Kral,et al.  A Modelica Library for Simulation of Elecric Energy Storages , 2011 .

[30]  Liangfei Xu,et al.  Energy flow modeling and real-time control design basing on mean values for maximizing driving mileage of a fuel cell bus , 2015 .

[31]  Hyunchul Ju,et al.  Nonisothermal Modeling of Polymer Electrolyte Fuel Cells I. Experimental Validation , 2005 .

[32]  Achim Kienle,et al.  A Model for the Freeze Start Behavior of a PEM Fuel Cell Stack , 2011 .

[33]  Adam Z. Weber,et al.  Effective Diffusion-Medium Thickness for Simplified Polymer-Electrolyte-Fuel-Cell Modeling , 2008 .

[34]  Qian Guo,et al.  Modeling of assisted cold start processes with anode catalytic hydrogen–oxygen reaction in proton exchange membrane fuel cell , 2013 .

[35]  Sichuan Xu,et al.  Experiment and simulation study on cold start of automotive PEMFC , 2011, 2011 International Conference on Electric Information and Control Engineering.

[36]  Hyunchul Ju,et al.  Large-scale cold start simulations for automotive fuel cells , 2014, 2014 5th International Renewable Energy Congress (IREC).

[37]  Nils Brandau,et al.  Analyse zur Zellinternen Befeuchtung eines Polymerelektrolytmembran-Brennstoffzellenstapels , 2012 .

[38]  Manish Khandelwal,et al.  An integrated approach for modeling of water and thermal transport in a polymer electrolyte fuel cell and stack , 2009 .

[39]  Sanggyu Kang,et al.  Dynamic simulation of a fuel cell hybrid vehicle during the federal test procedure-75 driving cycle , 2016 .

[40]  Sousso Kelouwani,et al.  A Comprehensive Review of Solutions and Strategies for Cold Start of Automotive Proton Exchange Membrane Fuel Cells , 2016, IEEE Access.

[41]  Roberto Cipollone,et al.  Model based Design and Optimization of a Fuel Cell Electric Vehicle , 2013 .

[42]  Meena Sundaresan,et al.  A Thermal Model to Evaluate Sub-Freezing Startup for a Direct Hydrogen Hybrid Fuel Cell Vehicle Polymer Electrolyte Fuel Cell Stack and System , 2004 .

[43]  Pucheng Pei,et al.  Water management of proton exchange membrane fuel cell based on control of hydrogen pressure drop , 2014 .

[44]  Chaoyang Wang,et al.  Analysis of Electrochemical and Thermal Behavior of Li-Ion Cells , 2003 .