Cold expansion of holes and resulting fatigue life enhancement and residual stresses in Al 2024 T3 alloy – An experimental study

Abstract This paper presents the experimental results of fatigue life enhancement and the residual stresses around the cold expanded holes in Al 2024, a widely used aerospace alloy. Two techniques for cold expansion of holes, namely split-sleeve with taper pin technique and split-sleeve with ball technique were considered for comparison, as the former involves surface contact and the latter has line contact during expansion. The techniques were compared based on the fatigue life enhancement in the expanded holes, the induced and the residual stresses due to expansion. The holes were expanded by 2%, 3%, 4%, 5%, and 6% using INSTRON machine in both the techniques. While both the techniques resulted in improvement in fatigue life of the expanded holes, the taper pin technique yielded 200% higher fatigue life improvement than that obtained by ball technique. The induced residual stresses were measured by mounting strain gages of 0.2 mm gage length. These are drawn as a function of induced strain. In both the techniques residual stresses increased with increase in percentage of expansion until 5% and then decreased for 6% expansion. The increase in fatigue life at 5% expansion was 1.88 times and 5.3 times higher than that of the non-expanded holes for ball and tapered method, respectively. The corresponding improvement in taper method was greater than the non-expanded holes. While, it was observed that the residual stresses decreased with respect to the distance from the hole in both the techniques, the ball technique resulted in lower residual stresses than that of taper pin technique.

[1]  Jeffrey Vogwell,et al.  A novel method of cold expansion which creates near‐uniform compressive tangential residual stress around a fastener hole , 2004 .

[2]  William N. Sharpe,et al.  An experimental study of fatigue crack initiation and growth from coldworked holes , 1979 .

[3]  Xiang Zhang,et al.  Fatigue life improvement in fatigue-aged fastener holes using the cold expansion technique , 2003 .

[4]  Lyndon Edwards,et al.  Measurement of the three-dimensional residual stress distribution around split-sleeve cold-expanded holes , 1996 .

[5]  Zhufeng Yue,et al.  Effect of cold expansion on fatigue performance of open holes , 2008 .

[6]  O. Buxbaum,et al.  Expansion of cracked fastener holes as a measure for extension of lifetime to repair , 1987 .

[7]  Jeffrey Vogwell,et al.  The effect of cold expansion on improving the fatigue life of fastener holes , 2003 .

[8]  Pravat Kumar Ray,et al.  Prediction of fatigue crack growth and residual life using an exponential model: Part II (mode-I overload induced retardation) , 2009 .

[9]  Xiang Zhang,et al.  Life enhancement of fatigue-aged fastener holes using the cold expansion process , 2000 .

[10]  Dl Ball,et al.  Experimental investigation on the effects of cold expansion of fastener holes , 1998 .

[11]  J. T. Maximov,et al.  The benefit from an adequate finite element simulation of the cold hole expansion process , 2009 .

[12]  Jeffrey Vogwell,et al.  Fatigue life of an aerospace aluminium alloy subjected to cold expansion and a cyclic temperature regime , 2006 .

[13]  A. Leon,et al.  Benefits of split mandrel coldworking , 1998 .

[14]  Abdelwaheb Amrouche,et al.  Numerical study of double cold expansion of the hole at crack tip and the influence on the residual stresses field , 2008 .

[15]  S. Pasta.  Fatigue crack propagation from a cold-worked hole , 2007 .

[16]  S. R. Daniewicz,et al.  Predicting the effect of residual stress on fatigue crack growth , 2007 .

[17]  W. H. Cathey,et al.  Fracture Mechanics Consideration of Residual Stresses Introduced by Coldworking Fastener Holes , 1980 .

[18]  M. J. Pavier,et al.  The effect of cold expansion on fatigue crack growth from open holes at room and high temperature , 2001 .