Modeling contact erosion in three phase vacuum contactors

A computer model was developed to simulate the unequal contact erosion measured in a contactor during three-phase AC-4 life testing. The model showed that the contact erosion is directly affected by the randomness of the time of the contacts. A probability distribution was created to simulate any degree of randomness in the opening. The model showed that repeated opening of the contactor at or near the same electrical phase angle over thousands of operations resulted in unequal contact erosion for each pole due to differences in arc energy. If there is a consistent imbalance in the arc energy one pole will erode at a significantly higher rate than the other two poles. The degree of unequal wear was dependent on the degree of randomness of contact part. The resulting unequal contact erosion would just amplify the unbalance with each subsequent operation leading to a run-away condition. A completely random opening resulted in even contact wear while synchronous opening resulted in unequal erosion. Synchronous opening of a contactor can occur from the inherent nature of the electromagnet used to operate the contactor. This model could also be used to simulate air contactor erosion.

[1]  A. Greenwood,et al.  Electrical transients in power systems , 1971 .

[2]  M. N. Nguyen,et al.  Low stress polymer die attach adhesive for plastic packages , 1994, 1994 Proceedings. 44th Electronic Components and Technology Conference.

[3]  B. Mirman.  Microelectronics and the Built-Up-Bar Theory , 1992 .

[4]  Douglas O. Powell,et al.  Flip-chip on FR-4 integrated circuit packaging , 1993, Proceedings of IEEE 43rd Electronic Components and Technology Conference (ECTC '93).

[5]  Ephraim Suhir.  Thermally induced interfacial stresses in elongated bimaterial plates , 1989 .

[6]  A. Bar-Cohen,et al.  Mechanistic figures of merit for die-attach materials , 1996, InterSociety Conference on Thermal Phenomena in Electronic Systems, I-THERM V.

[7]  E. K. Buratynski.  Analysis of Bending and Shearing of Tri-Layer Laminations for Solder Joint Reliability , 1998 .

[8]  Yung-Cheng Lee,et al.  Effects of Ceramic Ball-Grid-Array Package's Manufacturing Variations on Solder Joint Reliability , 1994, Proceedings of the International Conference on Multichip Modules.

[9]  W. Engelmaier.  Fatigue Life of Leadless Chip Carrier Solder Joints During Power Cycling , 1983 .

[10]  C. Discour,et al.  Erosion Behavior of Several AgCdO Materials-A Comparison Between Actual Contactors and a Testing Machine , 1979 .

[11]  B. Z. Hong,et al.  Nonlinear finite element simulation of thermoviscoplastic deformation of C4 solder joints in high density packaging under thermal cycling , 1994, Proceedings of 1994 4th Intersociety Conference on Thermal Phenomena in Electronic Systems (I-THERM).

[12]  J. Muniesa,et al.  Contact Erosion: Testing Machine and Switching Devices , 1983 .

[13]  G. Hill,et al.  Flip-chip encapsulation on ceramic substrates , 1993, Proceedings of IEEE 43rd Electronic Components and Technology Conference (ECTC '93).

[14]  A. S. Chen,et al.  A study of the interactions of molding compound and die attach adhesive, with regards to package cracking , 1994, 1994 Proceedings. 44th Electronic Components and Technology Conference.

[15]  Abhijit Dasgupta,et al.  A Nonlinear Multi-Domain Stress Analysis Method for Surface-Mount Solder Joints , 1996 .

[16]  A. Bar-Cohen,et al.  Thermo-structural behavior of underfilled flip-chips , 1996, 1996 Proceedings 46th Electronic Components and Technology Conference.

[17]  C. W. Nelson,et al.  Thermal stress in bonded joints , 1979 .