A Review of Indirect Tool Condition Monitoring Systems and Decision-Making Methods in Turning: Critical Analysis and Trends

The complex structure of turning aggravates obtaining the desired results in terms of tool wear and surface roughness. The existence of high temperature and pressure make difficult to reach and observe the cutting area. In-direct tool condition, monitoring systems provide tracking the condition of cutting tool via several released or converted energy types, namely, heat, acoustic emission, vibration, cutting forces and motor current. Tool wear inevitably progresses during metal cutting and has a relationship with these energy types. Indirect tool condition monitoring systems use sensors situated around the cutting area to state the wear condition of the cutting tool without intervention to cutting zone. In this study, sensors mostly used in indirect tool condition monitoring systems and their correlations between tool wear are reviewed to summarize the literature survey in this field for the last two decades. The reviews about tool condition monitoring systems in turning are very limited, and relationship between measured variables such as tool wear and vibration require a detailed analysis. In this work, the main aim is to discuss the effect of sensorial data on tool wear by considering previous published papers. As a computer aided electronic and mechanical support system, tool condition monitoring paves the way for machining industry and the future and development of Industry 4.0.

[1]  Xiaoli Li,et al.  A brief review: acoustic emission method for tool wear monitoring during turning , 2002 .

[2]  Stephen C. Veldhuis,et al.  Effect of secondary hardening on cutting forces, cutting temperature, and tool wear in hard turning of high alloy tool steels , 2015 .

[3]  Harun Akkuş,et al.  Statistical analysis of surface roughness in turning process , 2017 .

[4]  A. I. Azmi,et al.  Monitoring of tool wear using measured machining forces and neuro-fuzzy modelling approaches during machining of GFRP composites , 2015, Adv. Eng. Softw..

[5]  Tilo Pfeifer,et al.  Reliable tool wear monitoring by optimized image and illumination control in machine vision , 2000 .

[6]  Tomas Beno,et al.  Cutting temperatures during hard turning—Measurements and effects on white layer formation in AISI 52100 , 2014 .

[7]  Yaguo Lei,et al.  Applications of machine learning to machine fault diagnosis: A review and roadmap , 2020 .

[8]  Lin He,et al.  Prediction of Surface Roughness of 304 Stainless Steel and Multi-Objective Optimization of Cutting Parameters Based on GA-GBRT , 2019, Applied Sciences.

[9]  Ildikó Maňková,et al.  An approach to the microscopic study of wear mechanisms during hard turning with coated ceramics , 2015 .

[10]  N. R. Sakthivel,et al.  Tool condition monitoring techniques in milling process — a review , 2020 .

[11]  C. Y. Jiang,et al.  In-Process Monitoring of Tool Wear Stage by the Frequency Band-Energy Method , 1987 .

[12]  Samy E. Oraby,et al.  Tool life determination based on the measurement of wear and tool force ratio variation , 2004 .

[13]  Ning Li,et al.  Force-based tool condition monitoring for turning process using v-support vector regression , 2017 .

[14]  Ravinder Kumar,et al.  Study on surface roughness measurement for turning of Al 7075/10/SiCp and Al 7075 hybrid composites by using response surface methodology (RSM) and artificial neural networking (ANN) , 2015 .

[15]  R. Gandhinathan,et al.  Optimization of surface roughness and tool wear in hard turning of austempered ductile iron (grade 3) using Taguchi method , 2016 .

[16]  Weiwei Ming,et al.  Milling tool's flank wear prediction by temperature dependent wear mechanism determination when machining Inconel 182 overlays , 2016 .

[17]  S. K. Choudhury,et al.  Analytical modeling of tool health monitoring system using multiple sensor data fusion approach in hard machining , 2019, Measurement.

[18]  Roberto Teti,et al.  ANN tool wear modelling in the machining of nickel superalloy industrial products , 2011 .

[19]  Ship-Peng Lo.  The Application of an ANFIS and Grey System Method in Turning Tool-Failure Detection , 2002 .

[20]  Imtiaz Ahmed Choudhury,et al.  An innovative approach to monitor the chip formation effect on tool state using acoustic emission in turning , 2012 .

[21]  Mozammel Mia,et al.  Prediction of surface roughness in hard turning under high pressure coolant using Artificial Neural Network , 2016 .

[22]  Girish Kant,et al.  Optimization of Machining Parameters to Minimize Surface Roughness using Integrated ANN-GA Approach , 2015 .

[23]  Lin Li,et al.  Power signal separation in milling process based on wavelet transform and independent component analysis , 2011 .

[24]  Javier Rodríguez,et al.  Industrial application of a multitooth tool breakage detection system using spindle motor electrical power consumption , 2010 .

[25]  R. Polvorosa,et al.  An investigation of cutting forces and tool wear in turning of Haynes 282 , 2019, Journal of Manufacturing Processes.

[26]  M. Balaji,et al.  Optimization of drilling parameters for drilling of TI-6Al-4V based on surface roughness, flank wear and drill vibration , 2018 .

[27]  Krzysztof Jemielniak,et al.  Commercial Tool Condition Monitoring Systems , 1999 .

[28]  M. Elbah,et al.  Performance comparison of wiper and conventional ceramic inserts in hard turning of AISI 4140 steel: analysis of machining forces and flank wear , 2016 .

[29]  Danko Brezak,et al.  Tool wear estimation using an analytic fuzzy classifier and support vector machines , 2012, J. Intell. Manuf..

[30]  Mustafa Kuntoğlu,et al.  Investigation of signal behaviors for sensor fusion with tool condition monitoring system in turning , 2020 .

[31]  Andrés Bustillo,et al.  Artificial intelligence for automatic prediction of required surface roughness by monitoring wear on face mill teeth , 2017, Journal of Intelligent Manufacturing.

[32]  D. R. Salgado,et al.  Analysis of the structure of vibration signals for tool wear detection , 2008 .

[33]  Prithbey Raj Dey,et al.  Taguchi S/N based optimization of machining parameters for surface roughness, tool wear and material removal rate in hard turning under MQL cutting condition , 2018, Measurement.

[34]  Álisson Rocha Machado,et al.  A new approach for detection of wear mechanisms and determination of tool life in turning using acoustic emission , 2015 .

[35]  Ahmed A. D. Sarhan,et al.  Novel uses of SiO2 nano-lubrication system in hard turning process of hardened steel AISI4140 for less tool wear, surface roughness and oil consumption , 2014 .

[36]  Dustin Boswell,et al.  Introduction to Support Vector Machines , 2002 .

[37]  Geok Soon Hong,et al.  Wavelet analysis of sensor signals for tool condition monitoring: A review and some new results , 2009 .

[38]  Imtiaz Ahmed Choudhury,et al.  Application of acoustic emission sensor to investigate the frequency of tool wear and plastic deformation in tool condition monitoring , 2016 .

[39]  David Dornfeld,et al.  Sensor Integration Using Neural Networks for Intelligent Tool Condition Monitoring , 1990 .

[40]  Snr. D. E. Dimla.  The Correlation of Vibration Signal Features to Cutting Tool Wear in a Metal Turning Operation , 2002 .

[41]  C. Lee Giles,et al.  Learning and Extracting Finite State Automata with Second-Order Recurrent Neural Networks , 1992, Neural Computation.

[42]  Adam G. Rehorn,et al.  State-of-the-art methods and results in tool condition monitoring: a review , 2005 .

[43]  Balla Srinivasa Prasad,et al.  Correlation between vibration amplitude and tool wear in turning: Numerical and experimental analysis , 2017 .

[44]  Hamit Saruhan,et al.  The effect of vibration and cutting zone temperature on surface roughness and tool wear in eco-friendly MQL turning of AISI D2 , 2020 .

[45]  Tadeusz Mikolajczyk,et al.  Modeling of Cutting Parameters and Tool Geometry for Multi-Criteria Optimization of Surface Roughness and Vibration via Response Surface Methodology in Turning of AISI 5140 Steel , 2020, Materials.

[46]  Zhanqiang Liu,et al.  Influences of coating thickness on cutting temperature for dry hard turning Inconel 718 with PVD TiAlN coated carbide tools in initial tool wear stage , 2020 .

[47]  J. Kopac,et al.  Acoustic emission signals for tool wear identification , 1999 .

[48]  D. E. Dimla,et al.  Sensor signals for tool-wear monitoring in metal cutting operations—a review of methods , 2000 .

[49]  H. V. Ravindra,et al.  Optimization of machining parameters in turning Nimonic-75 using machine vision and acoustic emission signals by Taguchi technique , 2019, Measurement.

[50]  S. Liang,et al.  Predictive modeling of surface roughness in grinding , 2003 .

[51]  Hakki Ozgur Unver,et al.  Review of tool condition monitoring in machining and opportunities for deep learning , 2020, The International Journal of Advanced Manufacturing Technology.

[52]  Turgay Kıvak,et al.  The effect of addition of hBN nanoparticles to nanofluid-MQL on tool wear patterns, tool life, roughness and temperature in turning of Ni-based Inconel 625 , 2019, Tribology International.

[53]  Abdullah Aslan,et al.  Optimization and analysis of process parameters for flank wear, cutting forces and vibration in turning of AISI 5140: A comprehensive study , 2020 .

[54]  Eiji Shamoto,et al.  Influence of vibration in cutting on tool flank wear: Fundamental study by conducting a cutting experiment with forced vibration in the depth-of-cut direction , 2019, Precision Engineering.

[55]  Ruqiang Yan,et al.  Learning to Monitor Machine Health with Convolutional Bi-Directional LSTM Networks , 2017, Sensors.

[56]  Ashraf A. Kassim,et al.  Application of image and sound analysis techniques to monitor the condition of cutting tools , 2000, Pattern Recognit. Lett..

[57]  Wei Xue,et al.  Review of tool condition monitoring methods in milling processes , 2018 .

[58]  Vishal Wayal,et al.  Tool Condition Monitoring System: A Review , 2015 .

[59]  M. F. DeVries,et al.  Neural Network Sensor Fusion for Tool Condition Monitoring , 1990 .

[60]  Nabil Jouini,et al.  Relevance of roughness parameters of surface finish in precision hard turning. , 2014, Scanning.

[61]  Mahir Uzun,et al.  Effect of Cr particulate reinforcements in different ratios on wear performance and mechanical properties of Cu matrix composites , 2018 .

[62]  Ming Li,et al.  Effect of cutting parameters on surface roughness using orthogonal array in hard turning of AISI 1045 steel with YT5 tool , 2017 .

[63]  W. S. Yip,et al.  Tool life enhancement in dry diamond turning of titanium alloys using an eddy current damping and a magnetic field for sustainable manufacturing , 2017 .

[64]  D. R. Salgado,et al.  An approach based on current and sound signals for in-process tool wear monitoring , 2007 .

[65]  Jinxing Wu,et al.  Tribological Performance of Micro-Groove Tools of Improving Tool Wear Resistance in Turning AISI 304 Process , 2020, Materials.

[66]  P. S. Heyns,et al.  A comparative evaluation of neural networks and hidden Markov models for monitoring turning tool wear , 2005, Neural Computing & Applications.

[67]  David Dornfeld,et al.  A study of tool wear using statistical analysis of metal-cutting acoustic emission , 1982 .

[68]  J. Paulo Davim,et al.  Relationship between cutting force and PCD cutting tool wear in machining silicon carbide reinforced aluminium , 2000 .

[69]  Huicheng Zhou,et al.  A tool breakage monitoring method for end milling based on the indirect electric data of CNC system , 2018, The International Journal of Advanced Manufacturing Technology.

[70]  A. F. Whiting.  Identification , 1960, Australian Water Bugs. (Hemiptera - Heteroptera, Gerromorpha & Nepomorpha).

[71]  Carlos Henrique Lauro,et al.  Monitoring and processing signal applied in machining processes – A review , 2014 .

[72]  Fan Zhang,et al.  A Machine Vision Approach to Tool Wear Monitoring Based on the Image of Workpiece Surface Texture , 2010 .

[73]  Tuğrul Özel,et al.  Prediction of flank wear by using back propagation neural network modeling when cutting hardened H-13 steel with chamfered and honed CBN tools , 2002 .

[74]  Andres Bustillo,et al.  Machine-learning for automatic prediction of flatness deviation considering the wear of the face mill teeth , 2020, Journal of Intelligent Manufacturing.

[75]  Klaus-Dieter Thoben,et al.  "Industrie 4.0" and Smart Manufacturing - A Review of Research Issues and Application Examples , 2017, Int. J. Autom. Technol..

[76]  Salim Belhadi,et al.  Cutting Conditions Modeling and Optimization in Hard Turning Using RSM, ANN and Desirability Function , 2018, Journal of Failure Analysis and Prevention.

[77]  Harsh Y. Valera,et al.  Experimental Investigation of Surface Roughness and Power Consumption in Turning Operation of EN 31 Alloy Steel , 2014 .

[78]  Ch Sateesh Kumar,et al.  Experimental and numerical investigations on the effect of varying AlTiN coating thickness on hard machining performance of Al2O3-TiCN mixed ceramic inserts , 2017 .

[79]  Berend Denkena,et al.  Influence of cutting edge geometry on tool wear performance in interrupted hard turning , 2015 .

[80]  David Kerr,et al.  Assessment and visualisation of machine tool wear using computer vision , 2006 .

[81]  Fritz Klocke,et al.  Development of a tool wear-monitoring system for hard turning , 2003 .

[82]  Robert X. Gao,et al.  Deep learning and its applications to machine health monitoring , 2019, Mechanical Systems and Signal Processing.

[83]  Vishal S. Sharma,et al.  A review of empirical modeling techniques to optimize machining parameters for hard turning applications , 2016 .

[84]  Z.M. Li,et al.  Incremental learning for online tool condition monitoring using Ellipsoid ARTMAP network model , 2015, Appl. Soft Comput..

[85]  Stephen C. Veldhuis,et al.  Cutting temperature effect on PCBN and CVD coated carbide tools in hard turning of D2 tool steel , 2015 .

[86]  Yoke San Wong,et al.  Multiclassification of tool wear with support vector machine by manufacturing loss consideration , 2004 .

[87]  Michael McDonald,et al.  Fundamentals of Modern Manufacturing: Materials, Processes and Systems , 2016 .

[88]  Danil Yu. Pimenov,et al.  Investigations of surface quality and energy consumption associated with costs and material removal rate during face milling of AISI 1045 steel , 2020 .

[89]  Debasis Sengupta,et al.  Cutting force-based real-time estimation of tool wear in face milling using a combination of signal processing techniques , 2007 .

[90]  Krzysztof Dudzik,et al.  The Possibility of Applying Acoustic Emission and Dynamometric Methods for Monitoring the Turning Process , 2020, Materials.

[91]  T. Özel,et al.  Effects of cutting edge geometry, workpiece hardness, feed rate and cutting speed on surface roughness and forces in finish turning of hardened AISI H13 steel , 2005 .

[92]  Roshun Paurobally,et al.  A review of flank wear prediction methods for tool condition monitoring in a turning process , 2012, The International Journal of Advanced Manufacturing Technology.

[93]  Tamas Szecsi,et al.  A DC motor based cutting tool condition monitoring system , 1999 .

[94]  Sam Turner,et al.  Tool wear monitoring using naïve Bayes classifiers , 2014, The International Journal of Advanced Manufacturing Technology.

[95]  Diptikanta Das,et al.  Cutting temperature and tool flank wear during turning aluminium matrix composite in air-water spray environment - a Taguchi approach , 2018 .

[96]  H. Düzcükoğlu,et al.  The effects of harsh aging environments on the properties of neat and MWCNT reinforced epoxy resins , 2021 .

[97]  Tarek Mabrouki,et al.  Modeling and optimization of hard turning of X38CrMoV5-1 steel with CBN tool: Machining parameters effects on flank wear and surface roughness , 2011 .

[98]  Gang Yu,et al.  Analytical model for tool wear monitoring in turning operations using ultrasound waves , 2000 .

[99]  Weiwei Ming,et al.  Tool wear evaluation under minimum quantity lubrication by clustering energy of acoustic emission burst signals , 2019, Measurement.

[100]  Ravindra Nath Yadav,et al.  A hybrid approach of Taguchi-Response Surface Methodology for modeling and optimization of Duplex Turning process , 2017 .

[101]  George Liu,et al.  Online monitoring and measurements of tool wear for precision turning of stainless steel parts , 2013 .

[102]  Bing Wang,et al.  Investigation of surface topography and its deterioration resulting from tool wear evolution when dry turning of titanium alloy Ti-6Al-4V , 2019, Tribology International.

[103]  Shankar Chakraborty,et al.  Parametric optimization of some non-traditional machining processes using artificial bee colony algorithm , 2011, Eng. Appl. Artif. Intell..

[104]  Amlana Panda,et al.  Adaptive tool condition monitoring system: A brief review , 2020 .

[105]  Che Hassan Che Haron,et al.  Online tool wear prediction system in the turning process using an adaptive neuro-fuzzy inference system , 2013, Appl. Soft Comput..

[106]  Krzysztof Jemielniak,et al.  Tool failure detection based on analysis of acoustic emission signals , 1998 .

[107]  E. García Plaza,et al.  Analysis of cutting force signals by wavelet packet transform for surface roughness monitoring in CNC turning , 2018 .

[108]  Branislav Micieta,et al.  Detection of tool breakage during hard turning through acoustic emission at low removal rates , 2015 .

[109]  Srinivasa Rao Ch,et al.  Effect of Machining Parameters on Tool Wear in Hard Turning of AISI D3 Steel , 2014 .

[110]  Q. Yu,et al.  Experimental study on correlation between turning temperature rise and turning vibration in dry turning on aluminum alloy , 2019, The International Journal of Advanced Manufacturing Technology.

[111]  Ercan Öztemel,et al.  Literature review of Industry 4.0 and related technologies , 2018, J. Intell. Manuf..

[112]  B. B. Choudhury,et al.  Optimization of Surface Roughness Using Taguchi Methodology & Prediction of Tool Wear in Hard Turning Tools☆ , 2015 .

[113]  Bernhard Sick,et al.  ON-LINE AND INDIRECT TOOL WEAR MONITORING IN TURNING WITH ARTIFICIAL NEURAL NETWORKS: A REVIEW OF MORE THAN A DECADE OF RESEARCH , 2002 .

[114]  Enrique Alegre,et al.  On-line tool wear monitoring using geometric descriptors from digital images , 2007 .

[115]  Paweł Twardowski,et al.  Prediction of Tool Wear Using Artificial Neural Networks during Turning of Hardened Steel , 2019, Materials.

[116]  M. Vahdati,et al.  Vibration-based estimation of tool major flank wear in a turning process using ARMA models , 2015 .

[117]  Krzysztof Jemielniak,et al.  Advanced monitoring of machining operations , 2010 .

[118]  Adem Çiçek,et al.  The effects of CryoMQL conditions on tool wear and surface integrity in hard turning of AISI 52100 bearing steel , 2020 .

[119]  Tadeusz Mikolajczyk,et al.  Predicting tool life in turning operations using neural networks and image processing , 2018 .

[120]  Ferhat Yildirim,et al.  Application of grey relational analysis in high-speed machining of hardened AISI D6 steel , 2013 .

[121]  Vishal S. Sharma,et al.  Cutting tool wear estimation for turning , 2008, J. Intell. Manuf..

[122]  Ashok Kumar Sahoo,et al.  Performance studies of multilayer hard surface coatings (TiN/TiCN/Al2O3/TiN) of indexable carbide inserts in hard machining: Part-II (RSM, grey relational and techno economical approach) , 2013 .

[123]  D. K. Ojha,et al.  An economic and reliable tool life estimation procedure for turning , 2005 .

[124]  R. Viswanathan,et al.  Measurement and multi-response optimization of turning parameters for magnesium alloy using hybrid combination of Taguchi-GRA-PCA technique , 2020 .

[125]  Gilbert Gilibrays Ocen,et al.  Exponential Disruptive Technologies and the Required Skills of Industry 4.0 , 2020 .

[126]  Janez Kopac,et al.  Tool wear monitoring during the turning process , 2001 .

[127]  M. Guillot,et al.  On-line prediction of surface finish and dimensional deviation in turning using neural network based sensor fusion , 1997 .

[128]  Dongdong Kong,et al.  Relevance vector machine for tool wear prediction , 2019, Mechanical Systems and Signal Processing.

[129]  Elijah Kannatey-Asibu,et al.  Hidden Markov model-based tool wear monitoring in turning , 2002 .

[130]  Emin Salur,et al.  Mechanical properties and microstructure of composites produced by recycling metal chips , 2018, International Journal of Minerals, Metallurgy, and Materials.

[131]  Surjya K. Pal,et al.  Artificial neural network based prediction of drill flank wear from motor current signals , 2007, Appl. Soft Comput..

[132]  Ren Jie Kuo,et al.  Multi-sensor integration for on-line tool wear estimation through artificial neural networks and fuz , 2000 .

[133]  Tadeusz Mikolajczyk,et al.  Optimization and Analysis of Surface Roughness, Flank Wear and 5 Different Sensorial Data via Tool Condition Monitoring System in Turning of AISI 5140 , 2020, Sensors.

[134]  Elisabetta Ceretti,et al.  Analytical Models for Tool Wear Prediction During AISI 1045 Turning Operations , 2013 .

[135]  Enrique Alegre,et al.  Use of descriptors based on moments from digital images for tool wear monitoring , 2008 .

[136]  D. E. Dimla,et al.  On-line metal cutting tool condition monitoring.: I: force and vibration analyses , 2000 .

[137]  P. Sam Paul,et al.  A neural network model to predict surface roughness during turning of hardened SS410 steel , 2020, Int. J. Syst. Assur. Eng. Manag..

[138]  Weiming Shen,et al.  A sensor fusion and support vector machine based approach for recognition of complex machining conditions , 2018, J. Intell. Manuf..

[139]  Emin Salur,et al.  Experimental study and analysis of machinability characteristics of metal matrix composites during drilling , 2019, Composites Part B: Engineering.

[140]  L. D. Sirotenko,et al.  Surface Roughness of Steel in Turning with Metal Buildup on the Tool , 2019, Russian Engineering Research.

[141]  H. Sağlam,et al.  Investigation of progressive tool wear for determining of optimized machining parameters in turning , 2019, Measurement.

[142]  Amaresh Kumar,et al.  Study of surface roughness and flank wear in hard turning of AISI 4140 steel with coated ceramic inserts , 2015 .

[143]  Mingyuan Chen,et al.  Relationship between tool flank wear area and component forces in single point turning , 2002 .

[144]  Krzysztof Jemielniak,et al.  Application of AE and cutting force signals in tool condition monitoring in micro-milling , 2008 .

[145]  Steven Y. Liang,et al.  Analysis of acoustic emission in chatter vibration with tool wear effect in turning , 2000 .

[146]  R. Krishnamurthy,et al.  In-process tool wear and chip-form monitoring in face milling operation using acoustic emission. , 1994 .

[147]  Roberto Teti,et al.  Principal component analysis for feature extraction and NN pattern recognition in sensor monitoring of chip form during turning , 2014 .

[148]  Tadeusz Mikolajczyk,et al.  Neural network approach for automatic image analysis of cutting edge wear , 2017 .

[149]  Amlana Panda,et al.  Investigation of Flank Wear in Hard Turning of AISI 52100 Grade Steel Using Multilayer Coated Carbide and Mixed Ceramic Inserts , 2018 .

[150]  J. Rigal,et al.  Evolution during time of tool wear and cutting forces in the case of hard turning with CBN inserts , 2006 .

[151]  Masato Goto,et al.  The effect of oil mist supply on cutting point temperature and tool wear in driven rotary cutting , 2017 .

[152]  Rodolfo E. Haber,et al.  Tool wear monitoring using neuro-fuzzy techniques: a comparative study in a turning process , 2010, Journal of Intelligent Manufacturing.

[153]  Ekkard Brinksmeier,et al.  Cutting forces, tool wear and surface finish in high speed diamond machining , 2017 .

[154]  Jun Wang,et al.  Estimation of tool wear and optimization of cutting parameters based on novel ANFIS-PSO method toward intelligent machining , 2020, J. Intell. Manuf..

[155]  Bo-Suk Yang,et al.  Support vector machine in machine condition monitoring and fault diagnosis , 2007 .

[156]  Elijah Kannatey-Asibu,et al.  Analysis of Sound Signal Generation Due to Flank Wear in Turning , 2000, Manufacturing Engineering.

[157]  A. Ghani,et al.  Study of tool life, surface roughness and vibration in machining nodular cast iron with ceramic tool , 2002 .

[158]  Surjya K. Pal,et al.  Tool wear monitoring and selection of optimum cutting conditions with progressive tool wear effect and input uncertainties , 2011, J. Intell. Manuf..