Numerical study on performance of molten salt phase change thermal energy storage system with enhanced tubes

Abstract Based on enthalpy method, numerical studies were performed for high temperature molten salt phase change thermal energy storage (PCTES) unit used in a dish solar thermal power generation system. Firstly, the effects of the heat transfer fluid (HTF) inlet temperature and velocity on the PCTES performance were examined. The results show that although increasing the HTF inlet velocity or temperature can enhance the melting rate of the phase change material (PCM) and improve the performance of the PCTES unit, the two parameters will restrict each other for the fixed solar collector heat output. Then three enhanced tubes were adopted to improve the PCTES performance, which are dimpled tube, cone-finned tube and helically-finned tube respectively. The effects of the enhanced tubes on the PCM melting rate, solid–liquid interface, TES capacity, TES efficiency and HTF outlet temperature were discussed. The results show that compared with the smooth tube, all of the three enhanced tubes could improve the PCM melting rate. At the same working conditions, the melting time is 437.92 min for the smooth tube, 350.75 min for dimpled tube which is reduced about 19.9% and 320.25 min for cone-finned tube which is reduced about 26.9% and 302.75 min for helically-finned tube reduced about 30.7%. As a conclusion, the thermal performance of PCTES unit can be effectively enhanced by using enhanced tube instead of smooth tube. Although, the HTF pressure drops for the enhanced tubes are also larger than that of the smooth tube, the largest pressure drop (1476.2 Pa) is still very lower compared with the working pressure (MPa magnitude) of the dish solar generation system. So, the pressure drops caused by the enhanced tubes could almost be neglected.

[1]  K. Kaygusuz,et al.  Experimental study on melting/solidification characteristics of a paraffin as PCM , 2007 .

[2]  Changying Zhao,et al.  Experimental investigations of porous materials in high temperature thermal energy storage systems , 2011 .

[3]  John Currie,et al.  Integrated collector storage solar water heater: Temperature stratification , 2009 .

[4]  Yu Wang,et al.  Heat transfer and hydrodynamics analysis of a novel dimpled tube , 2010 .

[5]  R. Webb.  Single-phase heat transfer, friction, and fouling characteristics of three-dimensional cone roughness in tube flow , 2009 .

[6]  Louay M. Chamra,et al.  Correlating heat transfer and friction in helically-finned tubes using artificial neural networks , 2007 .

[7]  F. Kuznik,et al.  Experimental assessment of a phase change material for wall building use , 2009 .

[8]  Luisa F. Cabeza,et al.  Review on thermal energy storage with phase change: materials, heat transfer analysis and applications , 2003 .

[9]  A. Mujumdar,et al.  Finite-element analysis of cyclic heat transfer in a shell-and-tube latent heat energy storage exchanger , 1997 .

[10]  Francis Agyenim,et al.  A review of materials, heat transfer and phase change problem formulation for latent heat thermal energy storage systems (LHTESS) , 2010 .

[11]  Wujun Zhang,et al.  Numerical simulation and parametric study on new type of high temperature latent heat thermal energy storage system , 2008 .

[12]  Kamil Kaygusuz,et al.  Thermal energy storage performance of paraffin in a novel tube-in-shell system , 2008 .

[13]  A. Sharma,et al.  Review on thermal energy storage with phase change materials and applications , 2009 .

[14]  Anica Trp,et al.  An experimental and numerical investigation of heat transfer during technical grade paraffin melting and solidification in a shell-and-tube latent thermal energy storage unit , 2005 .

[15]  Ming Fang,et al.  Effects of different multiple PCMs on the performance of a latent thermal energy storage system , 2007 .

[16]  Juan Xiao,et al.  Three-dimensional numerical study of heat transfer characteristics in the receiver tube of parabolic trough solar collector , 2010 .

[17]  Long Jian-you,et al.  Numerical and experimental investigation for heat transfer in triplex concentric tube with phase change material for thermal energy storage , 2008 .

[18]  Ya-Ling He,et al.  A MCRT and FVM coupled simulation method for energy conversion process in parabolic trough solar collector , 2011 .

[19]  Ya-Ling He,et al.  Numerical study on thermal energy storage performance of phase change material under non-steady-state inlet boundary , 2011 .

[20]  Zhengguo Zhang,et al.  Study on paraffin/expanded graphite composite phase change thermal energy storage material , 2006 .

[21]  J. Fukai,et al.  Improvement of thermal characteristics of latent heat thermal energy storage units using carbon-fiber brushes: experiments and modeling , 2003 .

[22]  A. Sari,et al.  Thermal conductivity and latent heat thermal energy storage characteristics of paraffin/expanded graphite composite as phase change material , 2007 .

[23]  Changying Zhao,et al.  Heat transfer enhancement of high temperature thermal energy storage using metal foams and expanded graphite , 2011 .

[24]  Pichai Namprakai,et al.  A new version of a solar water heating system coupled with a solar water pump , 2009 .

[25]  Bernard Franković,et al.  Analysis of the influence of operating conditions and geometric parameters on heat transfer in water-paraffin shell-and-tube latent thermal energy storage unit , 2006 .

[26]  D. Buddhi,et al.  Numerical heat transfer studies of the fatty acids for different heat exchanger materials on the performance of a latent heat storage system , 2005 .

[27]  Ya-Ling He,et al.  Numerical study on coupled fluid flow and heat transfer process in parabolic trough solar collector tube , 2010 .

[28]  J. Fukai,et al.  Thermal conductivity enhancement of energy storage media using carbon fibers , 2000 .

[29]  Elena Palomo Del Barrio,et al.  KNO3/NaNO3 – Graphite materials for thermal energy storage at high temperature: Part I. – Elaboration methods and thermal properties , 2010 .

[30]  Hamid Ait Adine,et al.  Numerical analysis of the thermal behaviour of a shell-and-tube heat storage unit using phase change materials , 2009 .